Fortinet Community

Now i make authentication in fortinac using persistent agent and passive agent and i configure LoginDialogDisabled to hide the popup login credentials but it still appears for first time user appears although i configure everything as per below article  can anyone advise if faces this problem

Hello everyone. We bought a Fortigate 71g (7.6.7). I have experience using OpenVPN on Mikrotik and Pfsense. It was very convenient for remote access and local DNS access. The point is, we need to provide remote access to people without providing a DNS domain and server; we bind users by IP addresses, and that was sufficient. The problem is that I can't get the IPSec Fortigate to work without providing clients with a DNS server. All requests start going through the VPN tunnel, and access to local domains and DNS is lost.Detecting the client's local DNS is not quite right. For example, OpenVPN has this block-outside-dns feature. Is there a solution?Tried:1) config vpn ipsec phase1-interface    edit "test1"        set dns-mode manual        set ipv4-dns-server1 0.0.0.0    nextend2) I tried unset ipv4-dns-server1,2,33) ipsec Mode config - manual4) in the client's config in XML:         <ipsecvpn>            <options>                <enabled>1</enabled>              

Please help meI want to set it up like this: I have FortiGate, a Ruijie managed switch, and several APs. FortiGate port 3 will connect to the switch, and the APs will connect to the switch as well. I want mobile devices connected to the APs to be on the same IP subnet as the FortiGate and Ruijie.

Hi all,I can see lots of posts about dual wan connections on the Fortigate with lots of solutions for different scenarios, however I'd still like some advice with my situation.We have a Fortigate 81F (firmware 7.4.12) at the main office.  It currently has one internet link (wan1).  This is used for internet traffic, as well as ipsec vpn from 4 remote sites.  These remote sites also use the Fortigate wan1 as their internet connection.We are using ospf to advertise routes between the main office and remote sites.  The Fortigate's default route is via our isp.We wish to get a second internet connection to connect to wan2.  This will be solely for the ipsec vpn; no link redundancy or load balancing (at this stage, perhaps in the future).  All internet access will be via wan1.In what I hope is a simple situation like this, would setting static routes to both wan1 and wan2 but setting a higher priority on wan2 be enough to prevent atttempts to use wan2 as the internet link?I see other option

The MyCanal website used to work on my site, but now it doesn't. When I check on my Forti account, I see that it's blocked. So I want to understand why Forti is blocking MyCanal now and what I should do.

Previously i have 5 AP under my WLC9800, then i add some APs and some existing APs is renamed. How Fortinac can sync with the new name and add new APs to the inventory? 

Dear community, I am working on a design where the customer wants 3 Fortigate units to be placed in their 3 DC’s and want them to be in HA(A/A or A/P).Is this achievable, as i see the FGCP needs less latency also even if i tweak in the HB counts and Dead timer, what other factors to be considered.Is there an alternative approach that can achieve this or a better other solution that may fit this scenario. Devices: 101 F , 400F 

Please tell me.Until recently, the following KB article, which describes a workaround for automatic firmware upgrades after End of Streaming (EoES), was available.However, it now displays "Access Denied." Technical Tip: Disable auto-upgrade for unlicensed FortiGateshttps://community.fortinet.com/t5/FortiGate/Technical-Tip-Disable-auto-upgrade-for-unlicensed-FortiGates/ta-p/414696 Please tell me why it has been made private.

Having an issue I’ve never seen before, I have a ticket open with TAC but figured I’d see if anyone has ever seen this before. As soon as I plug the modem into my Fortigate, the modem crashes constantly and will never get a lock on the ISP signal. As soon as I unplug it and connect a laptop directly to the modem, it is able to establish a lock and I get a public IP. This occurs both if I try to get a public IP using DHCP or if I try to set one of our static IPs. The ISP has tried two of their Router/Modem combo units, as well as we have tried two Arris Surfboards, one of which is known working on a different circuit. Thanks for any help!

Hi,For training purposes, I have installed FortiManager 8.0.0 on VMware and FortiGate 8.0.0, but I am encountering the following problem: I have already tried using the SSL certificate whose serial number is specified in the CN field, but the issue still persists. fgfm-allow-vm is enabled   

Can we use forticasb solution as standalone without fortigate, sase, or others?

Hey everyone I have been trying to login to our FortiCloud account to register couple of new FortiGates and im unable to because they security codes aren't being sent to our email. Also I did an passwort reset already and then I received an email. But I still dont receive the security code email while trying to login. Any ideas? 

Following table outline’s, a set of Dependencies and Key points to be considered and useful with planning a migration of SSL-VPN deployment to IPSEC-VPN based deployment. Below Table is an effort of consolidating the functionalities and capabilities for effective planning of a migration. Content has been extracted from official Fortinet documentations and have put into a table for quick reference.  FortiClient Version Dependencies Free Version - up to client Version 7.4.3 1. User Authentication through Local user database - IKEv1 - supported with XAUTH framework* - IKEv2 - Supported with EAP 2. User Authentication through LDAP - IKEv1- supported with XAUTH framework * - IKEv2 - Limitations with the way EAP framework operates EAP-TTLS method has to be used. FortiClient Free version has limitations of changing the EAP method. ** 3. User Authentication through RADIUS - IKEv1 - Supported with XAUTH Framework * - IKEv2 - Supported with EAP-MSCHAPv2

We use 600F and hosted switches and APs in the 7.2.13 system.After testing and TAC confirmation, the 600Fwith7.2 system will discard multicast of tunnel SSIDs.Users cannot use Airplay to discover Apple TV through tunnel SSID,even though I have already configured multicast and IPv4 policies according to KB.We have two suggestions, either use 'set capwap-offload disable' or try upgrading to 7.4 or higher for testing.But we currently do not plan to upgrade to 7.4 because it is not possible to directly configure switch ports such as "loop gurad" and "stp budp guard" on the web management page, and these features are precisely the reasons why we chose Fortinet.I would like to know if Fortinet will fix this bug in FortiiOS7.2?Thanks.

Servus Community,I'm trying to add a FortiGate-VM HA cluster (A-P) running FortiOS 7.4.11 to a FortiManager VM running 7.4.11. Both FortiGate VMs and the FortiManager VM are running in evaluation/trial mode.The cluster itself is healthy and synchronized. Network connectivity is fine and TCP/541 is reachable. I have also enabled:config system global set fgfm-allow-vm enableendWhen I try to add the FortiGate to FortiManager, the device discovery fails with "Probe failed".After enabling FGFM debugging, I noticed that the TLS handshake actually completes successfully. The FortiGate then sends its authentication information including the serial number:serialno=FGVMEVO4T9J2-XXXAt that point FortiManager rejects the session and logs:serial number (FGVMEVO4T9J2-XXX) in 'get' message doesn't match the subject CN (FortiGate) in peer's certificate.I then checked the certificates on both HA members.Both nodes have the same Fortinet_Factory certificate:Subject:CN = FortiGateThe certificate fingerpr

FortiWeb exporting and import ML learnings through API. I need to check the  Fortinet Developer Network (FNDN)  as to have FortiWeb in a staging environment that has ML enabled and then to export the ML learnings through API and import them on the production FortiWeb again through API will be really powerful thing. The production FortiWeb in this case does not need ML learning enabled actually enabled as maybe limiting on production the learning to fake IP as it is not needed and on Staging to the Staging Jump host or staging subnet or not limiting at all if the network is safely designed.    

Hi All,I would like to ask your help about BGP with my scenario.I have FG1 connect with some FG Spoke via MPLS and VPN tunnel. I configured BGP peer for each link with the neighbor is the ip of each link.I want to prevent FG1 advertise route learned from MPLS back to FG2 via VPN tunnel and vice versa. I tried with route map out and comminity and it work for mpls because there are separate mpls for spoke but for vpn tunnel I cant because the VPN tunnel is peering with other Spoke.Could someone advise me the solution for the scenario? 

Dear Fortinet Community,I am currently experiencing an issue with a FortiOS upgrade. I have unboxed two newly acquired FortiGate devices (200G and 90G), both of which are not yet license-activated.I attempted to upgrade their firmware to version 7.4.12. The FortiGate 200G was initially running 7.2.11, and I was able to upgrade it to 7.4.11, but the upgrade to 7.4.12 did not succeed. The FortiGate 90G was running 7.4.8, and I was unable to upgrade it to any other version.I am aware that from the 7.4.x branch onward, upgrades are generally limited to patch-level changes. However, in my case, this behavior is not consistent as expected.Any assistance in resolving this issue would be greatly appreciated.Best regards.

I have successfull sync my entra id group to the fortinac, however if i add someone to the group then why the user is not synced in fortinac?Example i add user1 to group IT then if i go to System-Groups-Remote Groups then the member still empty.

Hi, i tried to deploy FortiManager following this doc: https://docs.fortinet.com/document/fortimanager-private-cloud/8.0.0/microsoft-hyper-v-administration-guide/449452/creating-the-virtual-machineAdded a second Hard Disk in “IDE 0” Show me this error, i tried to create Fixed and Dynamically (in differents clear installations) but same error appears even when i have enough space.After this error i cant type in terminal. Any suggestion? 

FG-80FでHA構成を構築したが、「config firewall ssh local-key」の状態がPrimaryとSecondaryで異なるのはなんで？？ #Primaryconfig firewall ssh local-key    edit "Fortinet_SSH_RSA2048"        set password ENC AAAAELE8NqYyMBgEhQ7grTfXnpgDb0j1zQrGm/aSSQ1sqReRT3VeDXYDl6GmJTfjifhoYZqMV94zwzYt3BI8Li3/XhV3YaPXywj7lf2VBcKfDSbZbTvJO/8fw2pN25HAxq6I4/cd3ZX90abcxiEdz3oQ1adKVpy/75tzDx95iKJ04o6uTMByeivFhMvKizbm2xAEE1lmMjY3dkVA        unset private-key        unset public-key        set source built-in    next #Secondaryconfig firewall ssh local-key    edit "Fortinet_SSH_RSA2048"        set password ENC AAAAELE8NqYyMBgEhQ7grTfXnpgDb0j1zQrGm/aSSQ1sqReRT3VeDXYDl6GmJTfjifhoYZqMV94zwzYt3BI8Li3/XhVKqNqqBKwoZqTJvhlyp3Zj30tjCJrI4bRFjiacIgfgGLajHp73E3BtG700kjxkxzUMlTFHFg7OPISbONaK1IoYVL17IOcl6QzL6wR9NJMnLVlmMjY3dkVA        set private-key "-----BEGIN OPENSSH PRIVATE KEY-----b3BlbnNzaC1rZXktdjEAAAAACmFlczI1Ni1jdHIAAAAGYmNyeXB0AAAAGAAAABCEPyKnpOC7AuAUn8wkg717AAAAEAAAAAEAAAEXAAAAB3NzaC1yc2EAAAADAQABAAABAQC37dLSRQBZoOb49bsDn/YVhLuGlHio5XLLl9Dzy

I installed FortiClient VPN 7.4.3.1736 (forticlient_vpn_7.4.3.1736_amd64.deb) on Ubuntu 24.04 using the package downloaded from the official Fortinet website.The VPN itself appears to work correctly and I can successfully connect to my VPN gateway.However, every time I start FortiClient VPN, I always receive one or more popup messages reporting conflicts or errors related to NetworkManager. The popup then asks whether I would like to upload the error report.Although the VPN is functional, these error popups appear every time the application starts, which suggests there may be a compatibility issue or a missing component.I have already tried several troubleshooting steps suggested by ChatGPT, but none of them resolved the problem.I was also told that FortiClient VPN 7.4.4 or 7.4.5 might contain fixes for Ubuntu 24.04, but I cannot find these versions on the Fortinet download site.Could anyone please advise:- Is this a known issue with FortiClient VPN 7.4.3 on Ubuntu 24.04?- Are FortiCli

Hello,According to the FortiGate Administration Guide,  https://docs.fortinet.com/document/fortigate/8.0.0/administration-guide/155426web filters are applied in this order:URL filter FortiGuard Web Filtering Web content filter Web script filter Antivirus scanningI'm confused about the last step. Antivirus is a separate security profile, not a web filtering feature. Why is it included in the web filtering order? Is this order only relevant when both Web Filter and Antivirus profiles are applied to the same policy?also i see  that:…...The FortiGate’s WAD daemon sends the URLs to FortiGuard in real-time for category determination.is that the webfilter process by wad even if it in flow or proxy mode?    

Good day,I would like to verify that  whether the local network configuration, such as static route, traffic with security files,  will stop when deregister the device from Cloud managment, no not.BrgdsLiu Wei 

I may have missed this and hope this is not a repost. In the screenshot, we have isolated a custom view of 10 mins and the graph is showing the Bytes in GB. Is this right?