Solved

Kindly share the OID for Fortiweb-VM. Thank you.

Hello everyone,I am working with FortiNAC-F 7.4 and I have imported a Cisco Catalyst switch v3. The ports on the switch are in VLANs. I can read them on the device, but the problem is that I cannot retrieve certain endpoints on the ports. When I check the events on FortiNAC, I receive an error:SNMP Failure SNMP failed for device SW-INFO with message SNMP getNext/getBulk Failed for device: 10.30.5.0.2Can you please help me?FortiNAC 

I get this error when installing Fortinet SSO, what could be the reason? 

Hello, I'm trying to connect my FortiGate to FortiAnalyzer. My FortiAnalyzer(10.10.0.3) VM is in VLAN 10, directly connected to FortiGate A (10.10.0.254). I successfully connected FortiGate A to FortiAnalyzer. My problem is with FortiGate B. I created an IPsec tunnel between FortiGate A and FortiGate B and created rules (any to any) to allow traffic between VLAN 10 (A) and VLAN 40 (B), but I can't contact FortiAnalyzerfrom FortiGate B (10.40.0.254). On Fortigate B, if I want to ping FortiAnalyzer, I have to execute ping-options source 10.40.0.254. If I don't, it don't ping... Do you have any ideas? Thanks  ! 

Hi, I'm new in Fortinet world.I have set two lan on two different ports on my Fortigate 60s ,v7.2.8 build1639 (192.168.1.x and 192.168.21.x). But one of them is not able to go in internet. How have I to set the correct gateway on wan1, wich works for one of them?Thank you a lot 

I have a weird one. I was in the web interface, Policy & Objects, Addresses area, and I incorrectly added a filter on the "address" line rather than the column name. The filter condition was a "contains" and the value was 0, and that returned no data ("No results" shows in the arresses and address groups area). The bad news is that because there are no returned values, the spot where I put the filter can no longer be seen to undo the filter !  The filter persists after logging out and back in, also persists in VDOM change and return. It doesn't appear to be in the user profile information stored in the backup so I don't think I can manage it via CLI. Anyone with hints on how to clear it?Brett

Hi everyone, I need some help with an issue I’m encountering with my Fortigate setup. Setup Details:- Router: ZTE (configured in bridge mode)- Firewall: Fortigate Issue:Despite successfully configuring the ZTE router in bridge mode and connecting it to my Fortigate, the Fortigate is still receiving an internal IP address instead of a public IP. Additionally, my DDNS is only working within my local network. When I try to access it from outside over the internet, it doesn’t work. Steps I’ve Taken:1. Configured Bridge Mode:Verified that the ZTE router is set to bridge mode. 2. Fortigate WAN Interface: Configured the Fortigate WAN interface to obtain an IP address automatically via DHCP.3. MAC Address Cloning: Ensured the MAC address of the Fortigate is registered with my ISP (if required).4. Release and Renew IP: Attempted to release and renew the DHCP lease on the Fortigate WAN interface.5. Restarted Devices: Power cycled both the ZTE router and the Fortigate.&nb

Hi all,I have created a topology in the EVE-NG software where my FortiGate firewall is connected to a switch, and the switch is connected to the management cloud. Now I want to open my FortiGate firewall GUI in Chrome browser, but it’s not opening.FortiGate port 5: 192.168.100.16Gateway: 192.168.100.1(If I remove the static IP from port 5 and set it to DHCP, I can open the FortiGate GUI via the DHCP IP in Chrome.)Please help me.

Hi everyone, I've received an FCP FortiManager voucher from my organization. I'm wondering if it's possible to use this voucher code for the FortiCloud Security Administrator exam instead. If not, is it possible to exchange the voucher by opening a TAC? Thanks in advance for your help!

Hi everyoneI'm trying to setup a policy with virtual servers to divide the traffic from subdomain1.domain.com and subdomain2.domain.com to different synology nas. I set up the virtual servers: and then setup a policy: The problem is that i'm obtaining this error: What could be wrong? 

 Hello Expert, I have two 400E in a HA cluster .We use the default HA ports for Heartbeat interface but had to add redundancy using the lan port.(BR_DATA port8) After reviewing numerous documentation we found that this was not best practice since the lan port is heavy use for data.I would like to assigned a new deliciated port (24)  to be my  backup heartbeat and remove (BR_DATA (port8) but would need some guidance since this is a production environment.  Also to configure port 24 as heartbeat port are there any special configuration need prior to it being assigned . GuyOffice-1 (ha) # showconfig system haset group-name "trans_amt"set mode a-pset password g==????Swdeeset hbdev "ha" 200 "port8" 100set session-pickup enableset override disableset priority 200set monitor "port8"end Thank you 

Hello, I am new to FortiManager and have successfully imported my two devices and their respective VDOMs. I have placed a specific VDOM into a specific ADOM because I want my client to manage it autonomously.When I am in the specific ADOM, I can create a firewall rule without any issues. However, when I try to push the configuration to the Fortigate, the device is not found. Do you have any idea why this might be happening?   Thank you for your help!

Hello,I have the following setup:FG 60F at our HQ - LAN IP: 192.168.205.0/24FG 60F at our DC - LAN IP: 192.168.5.0/24L2TP clients connecting with Dial-up connection and getting IP from subnet 192.168.199.0/24HQ and DC are connected via site-to-site ipsec VPN and both subnets x.x.205.0/24 and x.x.5.0/24 can communicate. When I connect to HQ as a L2TP dialup user I can access the network on HQ x.x.205.0/24 but I cannot connect to DC. I add a policy on HQ which allows traffic from L2TP-VPN to DC but it is not working. Can anyone please help set this up so a dialup user will only have to connect to HQ to gain access also to DC?

 Hello,I'm having trouble configuring an SSL VPN on my FortiGate 40F device. I've been searching for the corresponding configuration tab, but I can't seem to locate it anywhere. I also checked the "Core" section under "Feature Visibility," but to no avail. My firmware version is 7.4.4.Could you please assist me in understanding why I'm unable to access the SSL VPN configuration? I greatly appreciate your help.Thank you,

Hello,I am in the process of learning and understanding FortiManager and what it can do for my FortiGates.    I have one FGT that I am working on that was in-sync with both Config and Policy.  I changed a policy object, added a local user and added it to a group, and proceeded to install the change to the FGT.  Upon review in the Installation preview it listed out a bunch of things that were going to be deleted on the FGT.  I did not make such config changes on the FMG nor did any of my co-workers.  The FGT had not been edited either, everything was in-sync prior to the changes on the FMG.   So... what mechanism determines what things are to be deleted? is there a way to see this in the GUI? can I alter this so that it doesn't delete things unless I say so?  is there a flag to check or something? Just trying to understand what this thing is doing so that I or my co-workers don't delete something important and so that I can exp

I have Fortimanager installed.  I added my fortigate devices and can see them in the Fortimanager but I can also see that when I make changes in Fortimanager to the Fortigates I do not see the changes reflected on the FortiGate.  I am also not seeing the logs from the fortigates on the Fortimanager even though its configured. Does anyone know of any good videos or the like showing how to add Fortigates to FM and how to manage the Fortigates in FM... I am running Forigates 7.4 and Fortimanager 7.2

We are in the process of moving from on prem Exchange to O365/Exchange Online hybrid deployment.Can anyone advise which ports should be forwarded:- From O365 to on prem Exchange.- From O365 to on prem AD servers. FG FMW is 7.4.4 (Not brave, forced by insurance to keep firmware up to date...) I have all ports and FQDN listed in Microsoft white papers entered and policy from on prem servers to O365 in place. I've been using all sorts of firewalls in the last 30 years but Fortigate's VIP is by far the weirdest thing ever. Good idea, but poorly implemented and very limited functionality. Thank you for any suggestion you may have. (Yes I did search the forums but I hope I don't have to RTFM) T  

HI AllRecently something has popped up, our work internet line is being maxed (40mb up and down line speed from the ISP), when i check under Fortiview Sources the bandwidth doesnt match whats being used which tells me something else is using the bandwidth, is there any other way to check. All traffic goes through the Fortigate, so Im a little stumped. Any advice? Fortigate 60F v7.0.12 build 0523  

Hi all,I have a configuration request from one of my client . They have 2 isps wan on their Fortigate soo they need to use separate dns for they wan link. And also they have different vlan created on lan interface and half are routed through isp1 anf half are routed through isp2 so now they need to Use separate Dns for they lan traffic passing through both isp link so how can i configure that ??? Please help 

I'm using the latest and greatest Forticlient (ver 5.2.2.0624) and I also have installed certificates from a Smart Card I use for other business. However, when I open the the Forticlient and try and use the SSL-VPN, I'll immediately get a prompt to install the smart card. I've verified that "Client Certificate" is NOT checked on the connection settings yet it continues to want and check the client certificates from the Smart Card. Need to find a way to get the Forticlient to NOT check for them without effecting the installed Smart Card certificates.

Looking for the effects of enabling DPD on IPSec tunnels using Dialup connections. We have a remote site with 2 ISP connections and our main site which also has 2 ISP connections. From each site, we have 2x tunnels connected on each ISP for a total of 4x tunnels. We ran into an issue where one of the ISPs went down, but traffic was not redirected over either of the remaining 2 tunnels. I want to enable DPD on these tunnels which is pretty straight forward, but I cannot find any information regarding the effects enabling DPD may have on a dialup connection and being a remote site, I don't want to inadvertently bring the site down. Any input or advice would be greatly appreciated!

Hi, hope you are doing well,I would like to confirm if the FortiMail 200F does not provide Data Loss Prevention (DLP) functionalities? Therefore, I will have to suggest a 400F instead for my client. Thank you.

Hello guys,I have a dual WAN scenario and honestly I have some doubt.I noticed that when the SD-WAN has been configured, I can't create any WAN to LAN policy.There is a way to create a NAT 1:1 SD-WAN -> LAN policy?Therefore, is this the the right way (set-up SD-WAN) to obtain this goal:if the WAN2 (WAN2) fails or run out of bandwith, then activate the WAN1TNX

Hello team.As far as I understand in 802.1x authentication there are two mechanism evolved to authenticate supplicant. The outer method than encapsulates and secure the eap messages (like PEAP and TTLS) and inner methods (like PAP and CHAP and ms-chap-v2). I can see that PEAP can be used along with mschapv2 and this is clear when I configure the supplicant. However, I am not sure what mschapv2 means when it is listed among other methods in Fortinac RADiUS configuration as outer method. And can mschapv2 used alone in 802.1x and how can I configure the supplicant correctly to use it.

 Hello, I'm trying to connect my FortiGate to FortiManager.   My FortiManager (10.10.0.2) VM is in VLAN 10, directly connected to FortiGate A (10.10.0.254). I successfully connected FortiGate A to FortiManager. My problem is with FortiGate B. I created an IPsec tunnel between FortiGate A and FortiGate B and created rules (any to any) to allow traffic between VLAN 10 (A) and VLAN 40 (B), but I can't contact FortiManager from FortiGate B (10.40.0.254). Do you have any ideas?