create new trunk in fortiswitch - unable to select some ports

[blackstark]

I have a pair of fortiswitches configured with mc-lag icl. im running into an issue when i attempt to create a trunk. I want to use port 21 on switch 1 and port 21 on switch 2 but i am not able to select them . they do not show in the list?

what is preventing this? i dont see any configuration on the ports... just seems weird. i should be able to use any ports I want. 

they are 24 port switches model 1024D. can anyone fortiswitch guru's chime in here? Thanks,  

[AEK]

They are probably used somehow in the configuration. Check if there is any reference to these interferences.

[LunarEcho]

Check if those ports are already assigned to something else, like maybe they're part of another VLAN or something. Also, verify if the switches are recognizing the ports correctly.

[hbac]

Hi @blackstark,

To check interface references, please refer to https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-Check-Referenced-Objects/ta-p/19481...

Regards, 

[fp1]

If you configure and activate MCLAG you have to be aware of namings of interface, port, physical port, trunk, and trunkgoup. 

For my understanding - or in my opinion:

a classical  trunk ( or classical portchannel (static, lacp active, lacp slave)) is located an one physical switch.

a trunkgroup ( also called MCLAG-Static, MCLAG-Active, MCLAG-Slave)  described a combination of a portgroup over two switches.

fswitch1 # show full-configuration switch interface esxr71_Mgmt_TG
config switch interface
edit "esxr71_Mgmt_TG"
set description ''
set native-vlan 999
unset allowed-vlans
unset untagged-vlans
set discard-mode none
set dhcp-snooping untrusted
set dhcp-snoop-learning-limit-check disable
set dhcp-snoop-option82-trust disable
set arp-inspection-trust untrusted
set stp-state enabled
set stp-loop-protection disabled
set stp-root-guard disabled
set stp-bpdu-guard disabled
set loop-guard disabled
set edge-port enabled
set rpvst-port disabled
set ip-mac-binding global
set auto-discovery-fortilink-packet-interval 5
set private-vlan disable
set igmp-snooping-flood-reports disable
set mcast-snooping-flood-traffic disable
set mld-snooping-flood-reports disable
set packet-sampler disabled
set sflow-counter-interval 0
set snmp-index 74
config qnq
set status disable
set stp-qnq-admin enable
end
set vlan-mapping-miss-drop disable
set vlan-tpid "default"
set trust-dot1p-map ''
set trust-ip-dscp-map ''
set default-cos 0
set qos-policy "default"
set ptp-policy "default"
set ptp-status enable
set sticky-mac disable
set log-mac-event disable
set nac disable
next
end

fswitch2 # show full-configuration switch trunk esxr71_Mgmt_TG
config switch trunk
edit "esxr71_Mgmt_TG"
set port-selection-criteria src-dst-ip
set description ''
set mode static
set bundle disable
set auto-isl 0
set fortilink 0
set isl-fortilink 0
set mclag enable
set static-isl disable
set static-isl-auto-vlan enable
set members "port24"
next
end

Example for a MC-LAG Static (without LACP) 

!!! TG=TrunkGroup

In the following Example we try to use native vlan 999 (untagged/access) to the Trunkgroup named esxr71_Mgmt_TG which bind physical port 24 of switch fswitch1 + fswitch2 to an MCLAG-Static for a static Portchannel for Vshere ESXI vswitch0 Management (called Nic-Teaming).

fswitch1 (esxr71_Mgmt_TG) ## show
config switch trunk
edit "esxr71_Mgmt_TG"
set mclag enable
set members "port24"
next
end

fswitch1 (esxr71_Mgmt_TG) # get
name : esxr71_Mgmt_TG
trunk-id : 1
port-selection-criteria: src-dst-ip
description : (null)
mode : static
bundle : disable
auto-isl : 0
fortilink : 0
isl-fortilink : 0
mclag : enable
static-isl : disable
static-isl-auto-vlan: enable
members : port24

fswitch1 # show switch interface esxr71_Mgmt_TG
config switch interface
edit "esxr71_Mgmt_TG"
set native-vlan 999
set snmp-index 74
next
end

fswitch1 # show full-configuration switch physical-port port24
config switch physical-port
edit "port24"
set cdp-status disable
set description "esxr71 Eth 13/1 vSwitch0 Mgmt VLAN 999"
set dmi-status global
set egress-drop-mode enabled
set flapguard disabled
set flow-control disable
set fortilink-p2p disable
set l2-learning enabled
set lldp-profile "default-auto-isl"
set lldp-status tx-rx
set loopback disable
set max-frame-size 9216
set priority-based-flow-control disable
set speed auto-module
set status up
set storm-control-mode global
next
end

----

!!! TG=TrunkGroup

fswitch2 (esxr71_Mgmt_TG) ## show
config switch trunk
edit "esxr71_Mgmt_TG"
set mclag enable
set members "port24"
next
end

fswitch2 (esxr71_Mgmt_TG) # get
name : esxr71_Mgmt_TG
trunk-id : 1
port-selection-criteria: src-dst-ip
description : (null)
mode : static
bundle : disable
auto-isl : 0
fortilink : 0
isl-fortilink : 0
mclag : enable
static-isl : disable
static-isl-auto-vlan: enable
members : port24

fswitch2 # show full-configuration switch physical-port port24
config switch physical-port
edit "port24"
set cdp-status disable
set description "esxr71 Eth 13/1 vSwitch0 Mgmt VLAN 999"
set dmi-status global
set egress-drop-mode enabled
set flapguard disabled
set flow-control disable
set fortilink-p2p disable
set l2-learning enabled
set lldp-profile "default-auto-isl"
set lldp-status tx-rx
set loopback disable
set max-frame-size 9216
set priority-based-flow-control disable
set speed auto-module
set status up
set storm-control-mode global
next
end

fswitch2 # show switch interface esxr71_Mgmt_TG
config switch interface
edit "esxr71_Mgmt_TG"
set native-vlan 999
set snmp-index 74
next
end

fswitch2 # diagnose switch physical-ports summary port24

Portname Status Tpid Vlan Duplex Speed Flags Discard
__________ ______ ____ ____ ______ _____ ____________ _________

port24 up 8100 999 full 10G ,TS, none

Flags: QS(802.1Q) QE(802.1Q-in-Q,external) QI(802.1Q-in-Q,internal)
TS(static trunk) TF(forti trunk) TL(lacp trunk); MD(mirror dst)
MI(mirror ingress) ME(mirror egress) MB(mirror ingress and egress)
CF (Combo Fiber), CC (Combo Copper) LL(LoopBack Local) LR(LoopBack Remote)

fswitch2 # diagnose switch mclag peer-consistency-check esxr71_Mgmt_TG

** Comparing "switch.trunk" config ....OK
** Comparing "switch.interface" config ....OK
** Comparing "switch.physical-port" config ....OK
** Comparing "switch.stp.instance" config ....OK

Comparing "LAG state"
-------------------
local ports port24
local inactive ports none
Peer ports port24
Peer inactive ports none
LAG state UP

Comparing "STP state"
-------------------
Local active-LAG ports port24
Local active ports FORWARDING
Remote active-LAG ports port24
Remote active ports FORWARDING

show / debug / verify:

show full-configuration switch interface esxr71_Mgmt_TG
show switch physical-port port24
show full-configuration switch trunk esxr71_Mgmt_TG
diagnose switch trunk list esxr71_Mgmt_TG
diagnose switch trunk summary esxr71_Mgmt_TG
diagnose switch physical-ports summary port24
diagnose switch mclag peer-consistency-check esxr71_Mgmt_TG

[CEMS]

Hi everyone I lived same issue same problem And I could not find any solution ,please help me how can I exactly same problem 

[fp1]

Can you specify your problem(s) with grafical snippset and /  or show commands ? 

[CEMS]

Yes I checked there is no references interface that why it reason but ı recognize when I change de a vlan on wifi switch controller for that switch inteface ,switch can not apply this configuration adn when I connect to switch cli ssh and I recognized that interface which I changed the vlan on fortigate< wifi siwitc controller < fortiswitch ports ,there is no change on switch cli,I mean I use fortilink and my swtiches are managed swtich but I can not change any configuration realy my swtich ,but it is i teresting I dont see any issue for that switch and it seems autharize to fortilink,maybe that the reason for my problem how can I solve that ?

[fp1]

Can your show the wanted vlan and the configuring port in the Gui ?