Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
Lsousa
New Contributor

Fortinet 1000D IPSEC With ASA 5512

I have a configuration done to a VPN ip sec between a cisco asa 10.0.100.110 anda a fortinet 10.0.100.114 in a network 10.0.100.109/29

 

the information i receive is:

 

Encryption Scheme IKE v1 Authentication Method Pre-shared key: A enviar out-of-band (telefone, SMS, IM) Diffie-Hellman Group Group 2 Encryption Algorithm AES-256 Hashing Algorithm SHA-1 Main or Aggressive Mode Main Mode IKE Lifetime (for renegotiation) 1440 minutes (86400 seconds) NAT Traversal Enabled Keepalive Interval: 10 seconds / Retry interval: 2 seconds Encapsulation Mode tunnel Encryption Algorithm ESP AES-256 Authentication Algorithm SHA-1 Perfect Forward Secrecy Group 2 IPSEC Lifetime (for renegotiation) 480 minutes (28800 seconds) Lifesize in KB (for renegotiation) Unlimited

 

I already done that configutarion and a i can not reach a public ip linked to the private ip of them the services i need to reach by the public ip 197.500.86.15 is Tcp:80 and 4001

 

can someone say-me how can i by the fortigate permite this configuration is something missing in this information?

8 REPLIES 8
Toshi_Esumi
Esteemed Contributor III

I assume Phase2 selctors are 0/0<->0/0 on both sides and the tunnel is up. Then make sure you have a route into the tunnel for the public IP you need to reach to at the FGT. From there you need to sniff packets if they're going into the tunnel. If they do, the problem is on the ASA side.

Lsousa

how can i see if the route is ok, and how can i sniff the packets?

Toshi_Esumi
Esteemed Contributor III

"get router info routing-t details 197.500.86.15" would show you the route it follows.

"diag sniffer packet VPN_INTERFACE 'host 197.500.86.15'" would show you the packets. But you have to disable ASIC offloading at the policies to see them in sniffing ("set auto-asic-offload disable").

Lsousa

I already do the command and the information is  "Network not in table" there is something that i need to do to put the public ip on the network 

Lsousa
New Contributor

yes i can ping the public ip 

 

i would like to get first the best way to create the IPSEC VPN

 

MY SCENARIO IS i have a tunnel network range with 3 ips eg: 10.1.100.152/29 with 10.1.100.153 my network, 10.1.100.158 the asa network.

 

I want to get a service: http, https, 5400,5401 of the public ip of the 194.234.117.147.

 

i create a ipsec tunnel and my remote gateway is  10.1.100.158 i do the phase 2 with a local address ip 10.1.100.153 and the remote ip 194.234.117.147. 

 

then i create a policy to get in to the public ip with the port:80

 

i have a static route with the gateway 10.1.100.158 and a destination is 194.234.117.147.

 

i can not get the service http .

 

so my question is whact is the correct way to do this job?

 

i can not bring up the vpn.

Lsousa
New Contributor

I already done This but i can not bring up the tunnel he still down

Lsousa
New Contributor

i try it, but it persist to show too many vpn i have 8. 

 

you have a command that i can see only the debug of one vpn?

Lsousa
New Contributor

once the vpn is created, whact the next steps to reach the services in the public ip?

Labels
Top Kudoed Authors