Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
Justinb
New Contributor II

reportd CPU Utilization often at 99%

Fortigate 90d running 5.4.2, happened on 5.4.1 as well.

Very often, my FG90D is at very high CPU utilization.

Diag sys top shows reportd is always the culprit.

 

I've tried a lot of things, and cannot resolve the issue.

Log Settings -> Enable Local Reports is off.

 

It has a very basic configuration, can easily be rebuilt.

Does anyone have any ideas?

(I've killed reportd, it comes back some time later.  I've tried different firmware versions, same problem)

Diag sys top results:

un Time:  18 days, 3 hours and 29 minutes
97U, 2N, 0S, 1I; 1839T, 1122F
         reportd     1404      R      97.4     0.8
          httpsd      132      S       0.7     1.4
          newcli     2512      R       0.7     0.8
          httpsd      133      S       0.3     1.4
          httpsd     2507      S       0.1     1.2
          cw_acd      108      S       0.1     1.1
            iked       86      S       0.1     0.7
       ipsengine     2363      S <     0.0     4.5
        dnsproxy      105      S       0.0     2.1
         pyfcgid     2484      S       0.0     1.7
         cmdbsvr       39      S       0.0     1.6
         pyfcgid     2483      S       0.0     1.5
         pyfcgid     2482      S       0.0     1.5
         pyfcgid     2481      S       0.0     1.4
       scanunitd     2371      S <     0.0     1.4
       scanunitd     2372      S <     0.0     1.4
       ipshelper     2362      S <     0.0     1.4
       scanunitd       85      S <     0.0     1.4
         sslvpnd       76      S       0.0     1.3
         miglogd       58      S       0.0     1.2
 
fg90d #  

 

16 REPLIES 16
ericll75

I never had any policies in learning mode, but just in case, I tried turning off Policy Learning in System Features.  It looked very promising, as I didn't experience high reportd CPU usage for several days.  Unfortunately, the problem occurred once again just now.

Justinb
New Contributor II

I opened a case on this problem.

I have a very basic config, and I'm able to make changes as requested by support.

They asked me to update to 5.4.4 build 1117, which is now running, and the problem occurred within an hour.

 

I will update if the problem gets resolved.

Justinb
New Contributor II

Note: There was an entry in the release notes for 5.4.4

In the "Resolved Issues" section, Bug ID 369778 says: FWF_90D daemon report takes 99% of CPU Time.

 

I'm not running a FWF, it is a FGT90DPOE, and the issue wasn't resolved.  I couldn't find any other reference to bug ID 369778.

 

ericll75

I also upgraded our Fortigate 90D to firmware 5.4.4 build 1117, and very soon experienced the problem again.  Thanks for opening that ticket, and please keep us updated with what you learn!

Justinb
New Contributor II

I had the problem immediately after updating to 5.4.4.  Within an hour, CPU spiked for two hours, again for reportd.

However, it hasn't occurred since then.

There are still occasional CPU spikes, but they don't last for hours (they last for less than my 5 minute polling interval).

 

It has been fine for almost a week.

 

I'm leaving the case open for Fortinet's standard 14 days, I will post here if it lasts the entire 2 weeks without repeating.

 

Justinb
New Contributor II

Finalizing the post for me.

5.4.4 resolved the issue.

As I said previously, there was a spike immediately after upgrading to 5.4.4 that led me to think it didn't resolve the issue, but CPU Utilization has been as expected in the two weeks since that particular spike.

GusTech

Had the same issue on a 90D with 99-100% CPU use in all versions from 5.4.2 up to 6.0.3. Followed upg. matrix

 

Still had max CPU.. Deactivated log to disk, CPU dropped down to 2%

Fortigate <3

Fortigate <3
Labels
Top Kudoed Authors