I have a Fortigate 100D. There are 2 ISP connections 1 for each WAN port. My primary lan goes out on the WAN1 port, standard setup. Works fine. I tried to create a second network using the DMZ port to go out the WAN2 port on the second ISP. It is a completely isolated network, that will host my guest WIFI and my own connections for setting up and updating equipment so my downloads don't swamp our main line.
Lan 10.186.0.0/16 out on WAN1 4.4.4.2
Static Route out 0.0.0.0 on GW 4.4.4.1
DMZ 192,168.88.0/24 out on WAN2 5.5.5.2
Static Route out 0.0.0.0 on GW 5.5.5.1
The FW rules are in place, I can wire it up and turn on the route but it doesn't work. If I disable the route for WAN1 temporarily the DMZ out on WAN2 works but of course that breaks LAN to WAN1 out. Had no issues getting this to work on the Juniper FW we had before, but for the life of me I can't get this one going. I have seen several people on the boards asking about similar issues, nothing exactly like mine, but no answers that work.
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Two options:
1. create two vdoms and put wan1 and primary LAN into vdom1, and put wan2 and DMZ in vdom2. They can have individual default route since they're separate routers/FWs.
2. use policy routes (PBR) to specify the source interface to choose either wan1 or wan2. You still need to have two default routes to both wan1 and wan2. distance/priority wouldn't matter if no other traffic exist other than from primary LAN and from DMZ.
I prefer 1 because of simplicity and security to separate guest network from corp one (PCI-DSS audit proof), but I already know some disagree since there are multiple posts almost same as yours and I commented the same.
Got a reminder to never do this stuff during working hours. Thought creating the new second VDOM would not be an issue. Turns out it killed our ability to connect to sites with SSL. I had to delete it not long after I created it though I have no idea as to why it did this. Any thoughts?
Which wan interface and IP is the SSL VPN built on? Once you split it into two vdoms both at two different router/FW so if you get in one side via the vpn, you can get to the other side unless you set up a vdom link and routes over it.
This is not a minor change. Unless your 100% sure what would happen, don't make changes outside of a maintenance window.
Not an SSL VPN in the picture, we were unable to visit SSL websites for some reason after creating the second VDOM. There were no ports or any set up of any kind in the second VDOM, the first default VDOM still seemed to be set up the same as before, but we were getting errors from the firewall when we tried to access an HTTPS:// website. I rushed to change it back and did not get a capture of the error unfortunately. I have not had time to experiment with it further.
Again, the second vdom you created is a completely new router/FW basically not sharing anything with the root (original/default vdom), like policies, address objects, routes, and so on. You have to duplicate whatever you created before if they need to be there as well and used with the traffic through it.
Just use a policy route to direct traffic from the DMZ subnet to WAN2. That's what it's there for.
And, RTFM (F like in 'Fine') before doing anything else. A FGT is not a Juniper. I know Junipers can have an internal routing table and an external one. That's Juniper's speciality. A regular router only supports one default route.
IMHO a VDOM for this purpose is sheer overkill. You will be dancing between VDOMs all the time, looking where a resource is located. Of course, might be different for an old geek :)
So the default route applies to the entire appliance. You will either have to attempt using some policy routes which I've found to only be semi-reliable or create a VDOM for your guest network. This creates a virtual "second" appliance that runs on the same hardware as the physical appliance. I've linked the Fortinet doc below because it does a much better job explaining than I can. Your current setup will become the "root" vdom and you can name the new vdom to whatever you like such as "guest" and manage them separately, including a separate default route. You will need to remove any references to your wan2 interface and then "move" it in the config to your new vdom if you take this route.
Hope that helps.
Not sure which codebranch you are on, but this link is the 5.4.4 version for VDOM. So far as I know not much has changed: https://docs.fortinet.com/d/fortigate-virtual-domains-5
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1696 | |
1091 | |
752 | |
446 | |
228 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.