FortiAuth - SNMP OID remaining tokens

[funkylicious]

Hi,

Hoping that someone could help in regards to the correct OID required to query FortiAuth-VM in order to get the number of FortiTokens available for usage, since the one I've found in a old forum post is not returning the correct value - https://community.fortinet.com/t5/Support-Forum/FortiAuthenticator-OIDs/td-p/228761

Upon querying, 1.3.6.1.4.1.12356.113.1.202.6.0 , I get a value of 244 which is more than the total amount of registered/available tokens in FAC-VM.

iso.3.6.1.4.1.12356.113.1.202.6.0 = INTEGER: 244

FortiToken Mobile

Used: 148

Populated: 155

Available: 7

Disabled: 0

Using .1.3.6.1.4.1.12356.113.1.202.3.0 returns the correct amount of tokens since I also got 1 Yubikey registered (populated).

iso.3.6.1.4.1.12356.113.1.202.3.0 = INTEGER: 156

FortiToken Mobile / Yubikey Tokens

Used: 148	Populated: 155	Available: 7	Disabled: 0
Used: 0	Populated: 1	Available: 1	Disabled: 0

I am trying to create a plugin in the internal monitoring platform in order to have a view of this info w/o accesing the webUI.

Thanks.

[pminarik · Accepted solution]

"facFortiTokenCount" (.1.3.6.1.4.1.12356.113.1.202.3.0) = Number of FortiTokens (in general) that exist in the config on the unit.

"facFortiTokenRemaining" (.1.3.6.1.4.1.12356.113.1.202.6.0) = Number of tokens that can still be added before reaching the licensing limit.

Essentially, if you go to the GUI and into Authentication > User Management > FortiTokens, you will see  "<X> / <Y> FortiTokens" at the bottom of the page. This is <number of tokens> / <total possible number of tokens> (=max limit).

The OIDs are mapped as <X> = facFortiTokenCount, <Y> - <X> = facFortiTokenRemaining

As far as I can tell from skimming through the MIB file, there isn't an OID that will give out detailed usage counts of tokens (assigned/unassigned).

If I can offer an alternative, you can use the REST API to pull info about tokens, and filter for them by state.

https://docs.fortinet.com/document/fortiauthenticator/6.6.2/rest-api-solution-guide/875895/fortitoke...

[pminarik · Accepted solution]

"facFortiTokenCount" (.1.3.6.1.4.1.12356.113.1.202.3.0) = Number of FortiTokens (in general) that exist in the config on the unit.

"facFortiTokenRemaining" (.1.3.6.1.4.1.12356.113.1.202.6.0) = Number of tokens that can still be added before reaching the licensing limit.

Essentially, if you go to the GUI and into Authentication > User Management > FortiTokens, you will see  "<X> / <Y> FortiTokens" at the bottom of the page. This is <number of tokens> / <total possible number of tokens> (=max limit).

The OIDs are mapped as <X> = facFortiTokenCount, <Y> - <X> = facFortiTokenRemaining

As far as I can tell from skimming through the MIB file, there isn't an OID that will give out detailed usage counts of tokens (assigned/unassigned).

If I can offer an alternative, you can use the REST API to pull info about tokens, and filter for them by state.

https://docs.fortinet.com/document/fortiauthenticator/6.6.2/rest-api-solution-guide/875895/fortitoke...

[funkylicious]

Hmm, ok.

Thanks for the clarifications, I will try the REST API in order to get the data that I need.

[funkylicious · Accepted solution]

/api/v1/fortitokenmobilelicenses/ - returns the value that i'm looking for, I just need to parse the output

/api/v1/fortitokens/ - appears to return info about each token available for allocation.

[solasko2]

There's an ipsec tunnel down trap but idk if there's a dead peer detected trap. This is afaik only logged into the device log.