Device is FG-60f running the latest 7.4 firmware.
I have 2 vlan switches set up. One routs traffic to wan1 and the other to wan2. I set up policies and routing policies for them and both are working fine.
Vlan switch 1 services subnet 192.168.2.0/24 and vlan switch 2 services subnet 192.168.3.0/24.
What I need to do is allow traffic between the two subnets.
When I set up firewall policies to allow traffic between source vlan switch 2 destination vlan switch 1, I can ping and access 192.168.2.1 from the 192.168.3.0/24 subnet, but I can't see any of the other devices/ips on the 192.168.2.0/24 subnet. Same thing with firewall policy source vlan switch 1 destination vlan switch 2.
Firewall policies:
Fortinet_Gateway (14) # show
config firewall policy
edit 14
set name "Vlan1"
set uuid 3961879a-900e-51ee-e003-307188be460d
set srcintf "internal"
set dstintf "Internal wan2"
set action accept
set srcaddr "internal"
set dstaddr "Internal wan2 address"
set schedule "always"
set service "ALL"
set profile-protocol-options "test"
set nat enable
next
end
Fortinet_Gateway # config firewall policy
Fortinet_Gateway (policy) # edit 15
Fortinet_Gateway (15) # show
config firewall policy
edit 15
set name "Vlan2"
set uuid 6964594a-900e-51ee-fb76-e2b129d79f1e
set srcintf "Internal wan2"
set dstintf "internal"
set action accept
set srcaddr "Internal wan2 address"
set dstaddr "internal"
set schedule "always"
set service "ALL"
set profile-protocol-options "test"
set comments " (Copy of InterVlan)"
next
end
Ok, so what am I doing wrong here?
TIA
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Hello Xaak,
What is this interface "internal" ?
What is the sub interface for Vlan switch 1 services subnet 192.168.2.0/24 ?
Do you see if the traffic is hitting the policy 14, or not?
-BR*
Additionally is there any reason using NAT in policy 14 :
set nat enable
-BR-
No particular reason for using nat. I tried it both with nat on and nat off, and when I captured the config it happed to be on.
Created on 12-04-2023 07:14 AM Edited on 12-04-2023 07:16 AM
I don't have any sub interfaces on vlan switch 1 or switch 2. internal is the actual interface name for what I called vlan switch 1.
So interface "internal" = Vlan switch 1 services subnet 192.168.2.0/24
Why are you using NAT in policy 14 :
set nat enable
-BR-
Created on 12-04-2023 07:30 AM Edited on 12-04-2023 07:36 AM
Correct
"internal" = vlan switch 1 services 192.168.2.0/24
"Internal wan2" = vlan switch 2 services 192.168.3.0/24
I set nat disable initially, when it didn't work as expected, I set nat enable to try. I just happend to capture the config while it was set to enable.
Not sure how your "Vlan1" is configured, but vlan tag 1 is reserved in FortiOS.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-Reserved-VLAN-ID-1/ta-p/270111
Toshi
Hi @Toshi_Esumi,
Coming to the rescue again :)
Both vlan switches have vlan id = 0 and have no vlans underneath them.
Hi,
What is "internal" interface configuration?
Do you have configured route?
BR
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1660 | |
1071 | |
751 | |
443 | |
219 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.