Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
Hieu
New Contributor II

FortiNAC VPN management with FortiGate (IPsec VPN)

Hi everyone,

I have a FortiNAC VPN management model with FortiGate (IPsec VPN).
I referred to the documents below but still do not understand some things:

https://docs.fortinet.com/document/fortinac-f/7.6.0/fortigate-vpn-integration/693309/what-it-does

https://docs.fortinet.com/document/fortinac-f/7.6.0/fortigate-vpn-integration/693309/configuring-for...

Please see the attached links for IP information, model, etc.

My questions:

Can FortiNAC's Isolation Interface (10.1.3.71/24) be used for both SSL VPN and IPsec VPN?

Where does the Isolation IP range 10.5.254.11 - 10.5.254.99 come from? Where is the gateway of that range?

When is the IP range 10.5.254.11 - 10.5.254.99 used?

1 Solution
ebilcari
Staff
Staff

Based on the mentioned IP subnets I guess you are referring to this article: Technical Tip: A simple network example of deploying VPN management with FortiGate

 

Yes, the same isolation interface can be used in FNAC and dedicated to all VPN integrations. It is recommended to configure the 'Layer 3 Virtual Private Network'. The main scope of this interface in this implementation type is to offer DNS services.

As explained also in the article:

'VPN IP Subnets' can also be used instead of the standard scope since there is no DHCP service used in this case, the IPs for the end hosts are provided by FortiGate. This will enable FortiNAC to respond to DNS requests that are coming from this subnet.

This range can be considered just as a list of source IPs that are able to get DNS service. The gateway is required to complete the configuration in FNAC but it doesn't play any role in this case.

 

Remember that the Same IP range is also used in the VPN Addresses configuration as shown in the troubleshooting section: 'e. The tag is not being sent.'

 

The range itself (as planning) is chosen in the SSL-VPN Settings done in FGT, first picture in the section '2. SSL VPN configuration in the FortiGate.'

- Emirjon
If you have found a solution, please like and accept it to make it easily accessible for others.

View solution in original post

2 REPLIES 2
ebilcari
Staff
Staff

Based on the mentioned IP subnets I guess you are referring to this article: Technical Tip: A simple network example of deploying VPN management with FortiGate

 

Yes, the same isolation interface can be used in FNAC and dedicated to all VPN integrations. It is recommended to configure the 'Layer 3 Virtual Private Network'. The main scope of this interface in this implementation type is to offer DNS services.

As explained also in the article:

'VPN IP Subnets' can also be used instead of the standard scope since there is no DHCP service used in this case, the IPs for the end hosts are provided by FortiGate. This will enable FortiNAC to respond to DNS requests that are coming from this subnet.

This range can be considered just as a list of source IPs that are able to get DNS service. The gateway is required to complete the configuration in FNAC but it doesn't play any role in this case.

 

Remember that the Same IP range is also used in the VPN Addresses configuration as shown in the troubleshooting section: 'e. The tag is not being sent.'

 

The range itself (as planning) is chosen in the SSL-VPN Settings done in FGT, first picture in the section '2. SSL VPN configuration in the FortiGate.'

- Emirjon
If you have found a solution, please like and accept it to make it easily accessible for others.
Hieu
New Contributor II

Thank you so much for these information. It's very helpful for me!

Announcements
Check out our Community Chatter Blog! Click here to get involved
Labels
Top Kudoed Authors