Solved

HiI use Fortigate 101F with v7.0.12 in TP mode, but broadcast drops occur.The configuration diagram is as follows.Normally, there is no problem and when I reboot the server, the communication between the PC and the server side L2 does not work.As a result of checking, the MAC address of L3 was not learned in vdomA.So I put the mac-address of L3 port2 into the mac-address-table of vdomA statically and it works normally. This doesn't happen very often, it happens very occasionally.I enabled broadcast-forward, why does this happen?   

Hi I have FortiNAC version 7.4.1.0451 and Fortigate version 7.2.11. FortiAP 432F, SSID(traffic mode = tunnel) is using WPA2 ENTERPRISE and radius is selected pointing to the fortinac.  Fortinac Winbind status is running and joined to the domain.I get access-reject error in log. radius not enabled on device.   

Hello,Summary:I have a MSSQL DB, and i have an application which sends its logs to custom tables.Task:Can I use the JDBC connection to connect to these custom tables, and retrieve the table's columns, then I create the parser? FortiSIEM 

I have created an InterVDOM link on my firewall (7.4.7), and it can renew existing leases, but I canot seem to be able to get any config which will enable new leases to be obtained / givenThe topology is a remote site has a VPN back to HQ.  The remote site has DHCP Relays configured, pointing to DHCP servers on the LAN.  The setup works perfectly when routing the traffic from our VPN vdom to our LAN vdom over the internal switching.  But once I try and route the traffic over an InterVDOM link, all traffic other than new DHCP leases work.  As soon as I disable the policy routes, the DHCP and everything else works.

Hello TeamAm inquiring if any user has been able to set custom  email notifications for the fortinac like  Authentication failures or a connected device  instead of using the default email .#Fortinac Email notifications

Hi Team,We have integrated the FortiGate firewall with FortiClient EMS and are currently in the process of applying posture checks, specifically focusing on enforcing Antivirus (AV) software compliance on vendor laptops.The tags created within FortiClient EMS are being correctly pushed to both the FortiGate firewall and the FortiClient. These tags have been referenced in a firewall policy associated with remote VPN access. However, we are encountering an issue: when the VPN connection is established and the EMS tag is active, the destination resources become unreachable, despite the antivirus being installed and running properly on the vendor's workgroup laptop.We are testing on Azure IdP user and create a separate user for the vendor.Conversely, when the EMS tag is not applied, the destinations are reachable without any issues.Could you please advise what might be causing this behavior and suggest possible steps to resolve it?Thank you for your support.

On my FG firewall I have defined MGMT as OOB / dedicated management, and the firewall is in L2 / Transparent mode. One interface PORT1 from firewall is connected to the switch VLAN-1 and MGMT on the same switch VLAN-1. In this case is there a possibility of L2 loops formation on Switch? 

Hello everyone, I recently uploaded some images from Fortinet on my eve-ng, however, it turns on and seconds later it turns off, has anyone had this problem? I have other images that work from Cisco etc.

Hi guys, Can i get some help here? This is my first experience with FortiSASE. I have 2 sites: 1 in NL & 1 in the USA + Remote users in NL, USA, and Bangkok)I'm planning to deploy 2 FortiGate in each site in Active Standby setup. Each FortiGate will have 2 internet uplinks.Would you please advise which deployment guide should I use? When checking the KB, i get lost!What i understood is that I've to create SPA tunnel to the FortiSASE and deploy BGP for routing. but in the KB there are so many types of deployments!The sites should be able to communicate with each other in a secure channel.The users should use the FortiSASE to connect to the internet.I would like to use the forticlient to access the fortigates via its management interface. I already registered the fortigates/licenses and chose 2 PoPs in Europe and 2 in USA. Thank you in advance. RegardsSaid I re  

I am trying to connect to a fortigate 80E running 7.4.7 to roll back a software version but I am having difficulty connecting to the console during the boot process. I can connect to the console port via putty when the Fortigate 80e is booted and up and running. Putty is set to 9600 8 n n 1 But when the system boots, the system outputs odd characters until the boot process is complete, then I get the login prompt I read that the Baud rate changes to 115200 during the bootloader stage and then returns to 9600. However, I have tried changing putty to 115200 and rebooting and I still get garbled output.I have tried 9600, 19200, 38400, 57600, and 115200 but all output bad characters. I have also tried a FortiGate 60E, which has the same issue. I have also tried a FortiGate 90D at 9600 and this works just fine. What are the correct settings for an 80e running 7.4.7?What else can I try? I don't understand why this is so dificult

I need to create a VDOM (named it VDOM-A) which will operate in Transparent mode with two interfaces. I want to set all firewall management using Root domain on MGMT with out of band. Is it mandatory to assign an IP address to VDOM-A at any level? In L2 mode, can it operate without assigning any IP to it?

Hi! I created a hardware switch interface type, with 2 physical ports, and cannot delete it.It's grayed out, even if I try to disable them. How is it possible to delete them, please? TY

Hello, we just changed a FG cluster and we have FG90G with 7.4.7. I know that 7.4.8 does not support SSL VPN anymore so I guess we have no other option than changing from SSL VPN to IPSec. I am trying to build up the IPSec connection same way like the SSL VPN but I cant connect. Of course standard IPSec DialUp connection is easy and always works but since we have a lot of Groups and I want to control them with Policies I dont get it running. Incomming Interface is clear, the same and I know that it doesnt block any trafficClient address range I use the same object SSL VPN rangeAccessible Networks all since I also have to route them to Azure and our VPNs (like SSL VPN)PSK I checked many times, this is 100% correctXAUTH Inherit from Policy So in the IPSec to LAN policy I just copied from SSL VPN the same range and my TEST User, destination and service all. I try to connect but I get in the Client a failure of wrong credentials and than VPN connection failed, chec

Hello everyone, I have read the documentation and multiple community posts, but I'm still confused if a FortiGate can act as an IPAM server alone? The documentation says the FortiGate can act as a standalone IPAM server:https://docs.fortinet.com/document/fortigate/7.4.8/administration-guide/166728/configure-ipam-locally-on-the-fortigate  But I also have seen community post that say the opposite:https://community.fortinet.com/t5/Support-Forum/IPAM-feature/td-p/312696 https://community.fortinet.com/t5/Support-Forum/IP-Address-Management-IPAM-feature-on-Fortigate-enable/td-p/260963  So can a FortiGate be a standalone IPAM server or no? The documentation isn't very specific for a standalone FortiGate that manages multiples networks or maybe I have missed that part. Also when I configure an interface on the FortiGate for IPAM, with rules and all, it doesn't configure the DHCP server on the interface. It leaves the DHCP pool blank even though screenshots wi

Hi everyone,I’m working with a FortiGate 100F where interfaces X1 and X2 (10 Gbps) are in a dedicated VDOM used only for public-facing web services. We’re using SD-WAN and Virtual Servers in ssl-mode half, with a wildcard certificate to handle incoming HTTPS traffic for different subdomains like cloud.mydomain.com and nest.mydomain.com.Here’s my situation:I’m not a networking expert — actually, I’m pretty new to FortiGate and still learning as I go. It’s a small company and we all wear many hats, so I do a bit of everything, from servers to firewalls to figuring out reverse proxies when needed :grinning_face_with_sweat:Inside the server called nest, I’ve got multiple virtual hosts configured (for Joomla, Unity, etc.), and I’d love to route incoming HTTPS traffic based on SNI — ideally sending requests for cloud.mydomain.com to one backend, and nest.mydomain.com to another, or at least letting a single server like nest receive the correct traffic and handle it based on the domain.From w

Hallo everyone. I recently started working for a company that has this network topology.I see that the Aruba switches are set to MСLAG with Fortiswitches, but from the Fortiswich side there are no MCLAG settings. At the same time, Fortiswiches are online and available through Fortigate. I tried to set up MСLAG on FortiSwitch, but I encountered the fact that the Aruba side is specified as native VLAN 4094, and there is no such VLAN on FortiSwitches, at least I don’t see it through Fortigate GUI.Should I create a new VLAN with ID 4094 or is it better to change the native VLAN on Aruba?I am confused that VLAN with ID 4094 is specified everywhere in Aruba settings as native and the network works.

In version 7.4.8 for Fortigate 90G, the support for SSL VPN has been removed. Why is there no mention of this in the documentation? I need the SSL VPN functionality on this device. Where can I address my complaint about the removal of functionality for this model without any warning?

Hi Team, Could someone please guide me on can we add fortisiem agent while have splunk agent is in the system ?  do we need add exceptions ? What to look for before adding agents ? Is there any performance issue ? @Secusaurus @Anthony_E 

Hello everyone.I have a question regarding the status of some hosts in FortiNAC that are showing as "Disabled Online". I have already checked the settings to find out the reason, but so far I have not been able to find the cause and resolve the issue. Has anyone else experienced this? If so, can you share what was done to resolve the issue?Thank you for your attention.

I have a firewall configured on Transparent mode (two interfaces, inside and outside). Also I have a MGMT interface connected to the same vlan. In this case can it form L2 Loops? What is best practice?

Hello,FortiClient 7.2.x (also 7.4.x) shows invalide certificate warning after every reboot of the client, also the setting to do this on ems are not enabled. Any idea?Fortinet says this normal.....  

Hello.  Does it matter if the mode of the policy and the mode of the web filter are different except when Fortigate's policy is flow mode and web filter is proxy mode? Thank you. 

IPSec VPN with SAML was configured according to https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-configure-Microsoft-Entra-ID-SAML/ta-p/307457. The configuration seems to be in place according to the documentation, but I get ERR_CERTIFICATE_INVALID (which is to be expected), but if I click 'Continue (unsafe),' the Script Error shows up. Error says 'Permission denied,' and the URL says 'about:blank.' If I click 'Yes' for 'Do you want to continue running scripts on this page,' it simply goes back to the untrusted certificate popup. It cycles back and forth indefinitely. Does anyone have an idea as to what I can try? Thank you.  

Hello Running FAZ 7.4.7  What does has this impact on (exceeding the daily logs license)?Does this mean new logs will not be saved?Or it has (something) related to TAC support?  

Hello, I'm trying to configure an IPsec tunnel to replace ssl-vpn, but i can't make split tunnel to work. I have split-tunnel enabled with just an internal network allowed, and a policy that explicity allows traffic to that network. The problem is, once connected, the tunnel pushes a default route to the client, so all the traffic goes thru the Fortigate.I already tried things i saw on this forum but nothing worked To add info; doesn't matter what config i do on the forti or client side, doing "route print" always show a default route to the Forti (when i'm connected).