Re: AWS tunnel issue

amrit · 12-30-2024

Description This article explains the default behavior of the route tag address object. Scope FortiGate v7.4.0+ Solution Route tag address objects were introduced in v7.4.0 Route Tag Address Objects As per the design, the route-tag objects can only b...

amrit · 12-30-2024

Description This article explains the configuration steps required for OSPF with virtual wire pair interfaces. Scope FortiGate. Solution Router 1 and 2 exchange OSPF hello packets through the FortiGate virtual wire pair interfaces (port9, port10). Vi...

amrit · 11-20-2024

Description This article explains the reason for the inactivity time expiring message in OSPF debugs. Scope FortiGate. Solution The default OSPF Hello interval on FortiGate is set to 10 seconds and the Dead interval is 40 seconds. The inactivity time...

amrit · 11-18-2024

Description This article describes the reason for the error 2221 in the FSSO collector agent logs. Scope FSSO CA. Solution In FSSO CA logs the error 2221 is displayed if the collector agent does not have enough permissions to get the user group infor...

amrit · 10-30-2024

Description This article explains how to check the historical total number of allowed or blocked sessions using Fortiview Sources. Scope FortiGate. Solution Go under Dashboard -> FortiView Sources. When the period is set to 'now,' this page displays ...

amrit · 10-26-2024

You may need a traffic generator or simulator software to test the actual difference becuase it will be unnoticeable in the lab environment. Please refer to this link to read more about the inspection modes https://docs.fortinet.com/document/fortigat...

amrit · 09-23-2024

If you are facing any issues with your Fortiap device's throughput, it is impossible to provide you with a solution without looking at the technical details of the traffic. So ATM my recommendation is to open a ticket with your FortiAP serial number.

amrit · 09-22-2024

Discussion forums are only supported in English. From the translation, I understand you are getting a slow speed (80Mbps) when connected to an access point. 1. What is your Fortigate model and Firmware version 2. What is the firmware version on Forti...

amrit · 09-14-2024

FortiOS 7.2.8 and 7.2.9 are stable versions. ForitOS 7.2.9 includes additional fixes. Also, FGSP has no relation with the firmware version so it should work fine regardless of the firmware version. So, the choice of firmware version is yours. We will...

amrit · 09-14-2024

please check these link to understand the routing behaviour in Fortigate https://community.fortinet.com/t5/FortiGate/Technical-Note-Routing-Change-and-Session-Fail-over-with-SD-WAN/ta-p/198076 https://community.fortinet.com/t5/FortiGate/Technical-Tip...

User Statistics

User Activity

Technical Tip: Unable to add a route-tag address object as the source in the firewall policy

Technical Tip: How to configure OSPF with virtual wire pair interfaces

Technical Tip: OSPF inactivity timer expire message in the debug logs

Technical Tip: FSSO collector agent error 2221

Technical Tip: how to check the historical total number of allowed or blocked sessions using Fortiview Sources

Re: Testing flow based and proxy based mechanisms ?

Re: Fortigate Wireless Speed Problem

Re: Fortigate Wireless Speed Problem

Re: The recommended version of FG-401F

Re: is traffic session

Re: AWS tunnel issue

Re: Intermittent site issue from Office to AWS

Re: Fortigate Wireless Speed Problem

Re: Fortigate Wireless Speed Problem

Re: Blocking IPV6 Traffic

Re: FGT 800D how to reset?

Re: WAD process restart impact

Re: Use single Forticlient for multiple organizati...

Re: Testing HA Failover with ISP Issues on FortiGa...

Re: Firewall blocked Fortinet Single Sing On Agent...

KCS

User Statistics

User Activity

You are leaving our website