Re: tunnel interface is not getting disable

KumarV · 03-29-2024

Description This article describes a given scenario, where the Admin is not able to block any website using Webfilter profile. FortiGate has a reliable connection with FortiGuard servers with full licensing as well. Admin also has Custom-deep-inspect...

KumarV · 12-27-2023

Description This article describes how to use an automation stitch to automatically prevent rogue IP addresses from accessing SSL-VPN. Many distinct rogue IP addresses attempt brute force assaults virtually every day in an attempt to login to SSL-VPN...

KumarV · 10-08-2023

Description This article describes how to fix the issue when the FortiGate GUI is not loading after the upgrade to v7.2.5. Scope FortiGate v7.2.5 and onwards. Solution Make sure to use the correct admin-sport. For example, the settings shown below us...

KumarV · 09-17-2023

Description This article describes how to allow RDP from a PC to a Windows Domain Controller using a non-Admin user Topology: The below topology diagram is used, where both the Domain controller and PC are behind the two different FortiGates, and FG1...

KumarV · 08-20-2023

Description This article describes how to assign the Interfaces on FortiGate-VM in AWS Cloud. This topology has been created to achieve: Public_FG1 -->Port1 an IP from 10.1.1.0/24 Private_FG1-->Port2 an IP from 10.1.2.0/24 HA_FG1 -->Port3 an IP from ...

KumarV · 04-13-2024

Hello @unknown1020 Please follow the link below: https://community.fortinet.com/t5/FortiGate/Technical-Tip-Free-up-memory-to-avoid-conserve-mode/ta-p/241415 Regards

KumarV · 04-07-2024

Hello, @rezafathi You can use the KB mentioned below. You will be able to create a automation stitch which would automatically add the rouge IP's in a group and then you can use that group in a firewall policy to block the access. https://community.f...

KumarV · 03-31-2024

Hello, You can run the command #di sniffer packet any "host x.x.x.x and port 3389" 4 0 l x.x.x.x the destination server If you see the packet leaving the Fortigate LAN interface (where your destination is connected to) then it is not Fortigate issue ...

KumarV · 02-04-2024

Hi @Simba 1)You have to configure SSLVPN listening on WAN Interface. 2) Once you have the VPN setup then you would need firewall policy from SSLVPN to DMZ. 3) You might have to enable the NAT on the firewall policy if there is any sort of windows def...

KumarV · 01-27-2024

Hi, Adding further to the answer, Please also make sure you disable all sort of Anitvirus installed on workstation. Thank you

User Statistics

User Activity

Technical Tip: The webfilter is not blocking any websites despite having the webfilter licensing with FortiGuard servers connected on FortiGate

Technical Tip: Permanently block rogue IPs from accessing the SSL-VPN automatically with an automation stitch

Technical Tip: Cannot access the GUI after the upgrade to v7.2.5

Technical Tip: How to allow RDP from a PC to a Windows Domain Controller using a non-Admin user

Technical Tip: Assign the Interfaces on FortiGate-VM in AWS Cloud

Re: conserve mode in FortiGate

Re: Ban ip in ips

Re: RDP connection via ssl vpn

Re: DMZ for RDP Gateway

Re: Cannot ping "some" devices over IPsec VPN

Re: tunnel interface is not getting disable

Re: VPN speed capped in version 7.2.6

Technical Tip: Permanently block rogue IPs from ac...

Re: Some VDOM stop sending traffing

Re: Warning Message on bandwidth limit exceeded

Re: Warning Message on bandwidth limit exceeded

KCS