Re: Forticlient IPSEC w/ SAML stuck in connecting

FortiArt · 03-11-2025

Description This article describes the reasons for and how to work around an issue with dial-up IPsec VPN when using encapsulate ESP packets within TCP fails after upgrading to FortiOS 7.4.x. Scope FortiGate v7.4.x. Solution After upgrading to FortiO...

FortiArt · 02-21-2025

Description This article describes how to allow Splashtop application traffic to pass through FortiGate. Scope FortiGate. Solution Scenario: Splashtop is a remote desktop application. In cases where there is a main outbound Internet Access policy tha...

FortiArt · 02-07-2025

Description This article explains how to connect to FortiGuard Services when Internet traffic is routed via SD-WAN IPSec VPN remote site B. Error message 'Unable to Connect to FortiGuard Servers' shows on the FortiGate Dashboard of site A. Scope Fort...

FortiArt · 01-13-2025

Description This article describes the reasons why FortiGate sees the Kerberos authentication session of the old user who, while logged-off, still attached to the newly logged-on user when using the same computer. It also shows a possible alternative...

FortiArt · 12-26-2024

Description This article describes possible reasons for SD-WAN members in performance SLA showing DOWN status given that probed server(s) is reachable. Scope FortiOS with SD-WAN. Solution Performance SLA is designed to reflect the performance status ...

FortiArt · 11-12-2024

Hi. Is this only happen with Chrome browser or other web browsers? Did you tired to use incognito/in-private and test? Hope this helps

FortiArt · 10-18-2024

Would you please confirm if the following is what you've on configured on fortigate: configure system central-management set type fortiguard end In addition you can check this troubleshooting article: https://community.fortinet.com/t5/FortiGate/Troub...

FortiArt · 10-17-2024

Try to use ZTNA rather than sslvpn as this is more secure as per: https://docs.fortinet.com/document/fortigate/7.0.0/new-features/194961/basic-ztna-configuration Hope this help

FortiArt · 10-08-2024

If the vlans are configured and attached to port2 you need to create firewall policies from the VPN interface to each vlan to be able to access resources on those vlans. Remember to add those vlans on accessible networks under VPN phase-1. If those v...

FortiArt · 10-07-2024

You can disable any security software running on the client side and check again. In addition you can run: diagnose sniffer packet any 'port xxx' 4 <- xxx is the non working printers port number Also, diagnose debug reset diagnose debug flow filter p...

User Statistics

User Activity

Troubleshooting Tip: Encapsulating ESP packets within TCP headers Fails After Upgrade to FortiOS 7.4.x

Technical Tip: Splashtop Application Traffic Blocked by FortiGate

Technical Tip: Connection to FortiGuard Services when Internet Traffic is routed via SD-WAN IPSec VPN Remote Site

Technical Tip: Kerberos Authentication session still attached to a Logged-off User in FortiGate

Technical Tip: Possible Reasons for SD-WAN Members in Performance SLA Show DOWN Status

Re: SSL errors when connected through SSL VPN

Re: Fortigate 100F does not sync with FortiCloud

Re: SSLVPN failed user login attempts constantly been seen

Re: IPsec VPN - Can't access internal network

Re: tcp reset from client - utm allowed

Re: Forticlient IPSEC w/ SAML stuck in connecting

Re: VPN Not Connecting to server

Re: Fortigate Radius

Technical Tip: Connection to FortiGuard Services w...

Troubleshooting Tip: Cloudflare's ECH Blocked Webs...

Re: Fortigate 100F does not sync with FortiCloud

Re: FortiClient SSL VPN - SSO/SAML Issue

Re: Where to find a log about phishing?

Re: Fortimanager could not add FTG device

Re: FSSO creating Issues when taking RDP of other ...

KCS

User Statistics

User Activity

You are leaving our website