Technical Tip: FortiGate monitoring script

Jackie_T · 10-01-2024

Description This article describes what happens if the seed file of FortiToken is with a CD. Scope FortiToken with CD. Solution FortiToken Hardware with CD, for example, FortiToken-200-CD is a hardware Token that comes with a CD. The CD contains all ...

Jackie_T · 09-30-2024

Description This article describes how to troubleshoot the error shown in GTP logs. Scope FortiOS with FortiCarrier. Solution The error 'response-hteid-doesn’t-match-request' means the Tunnel Endpoint Identifier in the create session respond packet d...

Jackie_T · 09-08-2024

Description This article describes how to troubleshoot the issue of service unreachable for the FortiToken Cloud after 7th September 2024. Scope FortiAuthenticator, FortiToken Cloud. Solution There is a change of public IP for the FortiToken Cloud se...

Jackie_T · 09-02-2024

Description This article describes the errors encountered when installing the FortiAuthenticator Windows agent and how to fix them. Scope FortiAuthenticator Agent for Windows. Solution Below error shown when installing the FortiAuthenticator Windows ...

Jackie_T · 08-20-2024

Description This article describes that after upgrading firmware from 7.2.6 to 7.2.8 or 7.4.x version, the WAN interface of FortiGate 100F/101F will not show the option to set speed with only the auto option left in the list. The other 1G copper inte...

Jackie_T · 09-30-2024

Hi, For simple setup, you can achieve this by configure ECMP routes.Mean both WAN1 and WAN2 will have same distance value set, but WAN1 will have higher priority value set.The link with higher priority value will be less preferred and stay as standby...

Jackie_T · 09-11-2024

Hello HS08, I believe you are looking for the default value for ospf cost bandwidth reference in FortiOS? There is a setting under "config router ospf" >> "set auto-cost-ref-bandwidth". The default value set is 1000, in megabits per second. Reference...

Jackie_T · 08-26-2024

Hi Shane, Yes, is top-down rule.If you have multiple vlans, I believe you already configure trunk to allow those vlans on the switch? You might want to check below:1. Ensure routing is configure correctly:#get router info routing-table allYou should ...

Jackie_T · 08-26-2024

Hi forsenGa, There is a KB as well for this:https://community.fortinet.com/t5/FortiGate/Technical-Tip-Authentication-fails-with-clock-skew-errors-in/ta-p/222360 Thanks.

Jackie_T · 08-26-2024

Hi Alan, Transparent mode (Layer 2 deployment) is for a deployment where you need to integrate the FortiGate into an existing network without changing the IP structure, while still allowing for security policies.Transparent mode does not perform NAT ...

User Statistics

User Activity

Technical Tip: Lost seed file for FortiToken Hardware with CD

Troubleshooting Tip: GTP Error: response-hteid-doesnt-match-request

Troubleshooting Tip: FortiToken Cloud service unreachable

Troubleshooting Tip: Runtime error (at 4:511) when installing FortiAuthenticator Windows Agent

Technical Tip: FortiGate 100F/101F Interface Speed Issue

Re: Need assistance - dual WAN

Re: OSPF Cost

Re: Fortigate 201F 7.6.0 LAN -> WAN ALL/ALL not working

Re: SAML clock skew issue

Re: Transparent mode

Technical Tip: FortiGate monitoring script

Technical Tip: FortiGate Disable Hardware Accelera...

Troubleshooting Tip: FortiOS to AWS VPN Anti-Spoof...

Technical Tip: Compatibilities of Hardware Switch ...

Troubleshooting Tip: Explaining the NPU Offload fi...

Re: How to increase (expand?) disk space

KCS