Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
James_G
Contributor III

FortiOS 6.4.4 is out!

10 REPLIES 10
ipranger
Contributor

YEAH :)

Fortigate 60E v7.x (GA)

Fortigate 60E v7.x (GA)
SecurityPlus

Upgraded a 60F from 6.4.3 to 6.4.4. So far no issues found.

 

When we upgraded to 6.4.3 we had the wireless issue and had to wtp-profile, edit "FortiAP-profile-name", set dtls-policy dtls-enabled to get traffic to pass. This hurt wireless speed but allowed it to pass traffic.

 

After upgrading to 6.4.4 we ran config wireless-controller wtp-profile, edit "FortiAP-profile-name", unset dtls-policy

 

This gave us good performance again.

SecurityPlus

Is it just me or is there an issue with 6.4.3 and 6.4.4 in regards to marking a wireless access point as Rogue. When I

try to mark an Unclassified AP ("?" Icon) as a Rogue AP or Suppressed Rogue AP via the GUI and click Apply, it says "Failed to save changes".

Tracer

It's Probably not just you, I've had this exact problem for probably 6 months now, Fails to save changes.

ipranger

Yes, among other things, these were reasons why my config made you completely from scratch after 10 years and many upgrades. I no longer have the issue of memory problems or save Rogue AP here. For this you can no longer connect to 5Ghz after about 1-2 days. Only a reboot of the AP's helps.

Fortigate 60E v7.x (GA)

Fortigate 60E v7.x (GA)
lubyou

Any major show stoppers in 6.4.4? 

SecurityPlus

Not that I have seen.

seadm

We're seeing issues with the syslog delivered UTM logs in version 6.4.4. All our "vm64 AWS" instances that we upgraded to 6.4.3 are logging UTM events fine through syslog. All the 6.4.4 machines are missing UTM data for us to identify what the root cause is. Both resulted in a blocked request. (See logs at the bottom.)

 

We tried an EICAR file download test and the file was blocked but there was nothing in the syslog to specifically identify it as an EICAR event.

 

Our configs are almost identical between the 6.4.3 and 6.4.4 machines (except for local variances for networks).

 

We opened a case with support but are asking to see if people are experiencing the same issue?

 

Version 6.4.4 was only available to us in the last week or so.

 

Both hosts share the same config blocks:

(Syslog config)   config log syslogd setting       set status enable       set server "10.224.0.89"       set mode udp       set port 514       set facility local4       set source-ip ''       set format default       set priority default       set max-log-rate 0       set interface-select-method auto   end (Policy config)

      edit 1           set status enable           set name "allow"           set uuid d007ffd4-6f31-51e8-00f8-20af0b5a45de           set srcintf "port1"           set dstintf "port1"           set srcaddr "INTERNAL"           set dstaddr "all"           set internet-service disable           set internet-service-src disable           unset reputation-minimum           set rtp-nat disable           set action accept           set schedule "always"           set schedule-timeout disable           set service "ALL"           set tos-mask 0x00           set anti-replay enable           set utm-status enable           set inspection-mode flow           set profile-type single           set profile-protocol-options "TN-Proxy"           set ssl-ssh-profile "TN-certificate-inspection"           set av-profile "TN-Virus"           set webfilter-profile "TN-Web"           set dnsfilter-profile 'TN-DNS'           set emailfilter-profile 'TN-Email'           set dlp-sensor 'TN-DLP'           set file-filter-profile 'TN-File'           set ips-sensor "TN-IPS"           set application-list "TN-App"           set voip-profile ''           set logtraffic utm           set logtraffic-start disable           set capture-packet disable           set auto-asic-offload enable           set permit-any-host disable           set permit-stun-host disable           set fixedport disable           set ippool disable           set session-ttl 0           set vlan-cos-fwd 255           set vlan-cos-rev 255           set wccp disable           set disclaimer disable           set email-collect disable           set natip 0.0.0.0 0.0.0.0           set diffserv-forward disable           set diffserv-reverse disable           set tcp-mss-sender 0           set tcp-mss-receiver 0           set comments ''           set block-notification disable           set replacemsg-override-group ''           set srcaddr-negate disable           set dstaddr-negate disable           set service-negate disable           set timeout-send-rst disable           set captive-portal-exempt disable           set dsri disable           set radius-mac-auth-bypass disable           set delay-tcp-npu-session disable           unset vlan-filter           set traffic-shaper ''           set traffic-shaper-reverse ''           set per-ip-shaper ''           set nat enable       next

 

Logs:

================================== Log for 6.4.4 pulling down an EICAR file via curl: Dec 22 13:37:55 FORTIGATE date=2020-12-22 time=13:37:54 devname="FORTIGATE-6.4.4" devid="XXXXXXXXXXXXXXX" eventtime=1608673075356948804 tz="-0800" logid="0000000013" type="traffic" subtype="forward" level="notice" vd="root" srcip=10.XXX.XXX.173 srcport=50968 srcintf="port1" srcintfrole="undefined" dstip=73.XXX.XXX.XXX dstport=80 dstintf="port1" dstintfrole="undefined" srccountry="Reserved" dstcountry="United States" sessionid=4222294 proto=6 action="close" policyid=1 policytype="policy" poluuid="f8bf71ea-18ad-51e7-3263-3e36007b6fd3" policyname="allow" service="HTTP" trandisp="snat" transip=10.XXX.XXX.184 transport=50968 appid=15893 app="HTTP.BROWSER" appcat="Web.Client" apprisk="medium" applist="TN-App" duration=30 sentbyte=356 rcvdbyte=5547 sentpkt=5 rcvdpkt=4 utmaction="block" countav=1 crscore=50 craction=2 ================================== Same logs for 6.4.3 pulling down an EICAR file via curl: Dec 22 13:38:07 10.XXX.XXX.98 date=2020-12-22 time=13:38:06 devname="FORTIGATE-6.4.3" devid="XXXXXXXXXXXXXXX" eventtime=1608673087572854902 tz="-0800" logid="0211008192" type="utm" subtype="virus" eventtype="infected" level="warning" vd="root" policyid=1 msg="File is infected." action="blocked" service="HTTP" sessionid=4954618 srcip=10.XXX.XXX.70 dstip=73.XXX.XXX.XXX srcport=47738 dstport=80 srcintf="port1" srcintfrole="undefined" dstintf="port1" dstintfrole="undefined" proto=6 direction="incoming" filename="eicar.txt" quarskip="Quarantine-disabled" virus="EICAR_TEST_FILE" dtype="Virus" ref="http://www.fortinet.com/ve?vn=EICAR_TEST_FILE" virusid=2172 url="http://XXX/eicar.txt" profile="TN-Virus" agent="curl/7.74.0" analyticscksum="131f95c51cc819465fa1797f6ccacf9d494aaaff46fa3eac73ae63ffbdfd8267" analyticssubmit="false" crscore=50 craction=2 crlevel="critical" Dec 22 13:38:41 10.XXX.XXX.98 date=2020-12-22 time=13:38:41 devname="FORTIGATE-6.4.3" devid="XXXXXXXXXXXXXXX" eventtime=1608673121980655620 tz="-0800" logid="0000000013" type="traffic" subtype="forward" level="notice" vd="root" srcip=10.XXX.XXX.70 srcport=47738 srcintf="port1" srcintfrole="undefined" dstip=73.XXX.XXX.XXX dstport=80 dstintf="port1" dstintfrole="undefined" srccountry="Reserved" dstcountry="United States" sessionid=4954618 proto=6 action="close" policyid=1 policytype="policy" poluuid="d007ffd4-6f31-51e8-00f8-20af0b5a45de" policyname="allow" service="HTTP" trandisp="snat" transip=10.XXX.XXX.98 transport=47738 appid=15893 app="HTTP.BROWSER" appcat="Web.Client" apprisk="medium" applist="TN-App" duration=34 sentbyte=488 rcvdbyte=64880 sentpkt=6 rcvdpkt=15 utmaction="block" countav=1 crscore=50 craction=2

lubyou
New Contributor

Went for 6.4.4, logged into one of our SSL VPN portals via browser, /bin/log_sea starts to max out the CPU until it is killed.

The firmware lottery never ends.

 

Edit:

 

log_sea CPU usage ultimately goes down, after the SSL VPN portal has listed the recent user history.

Disabling web-mode for the SSL VPN portals works around the issue.

 

Edit 2:

TAC response: "As per my understanding you are facing an issue with Log-SEA CPU. Please be informed that this is caused by the log history in the webportal. So you can disable the history for all the portals. Please be informed that this is by design."

Labels
Top Kudoed Authors