FortiGate
FortiGate Next Generation Firewall utilizes purpose-built security processors and threat intelligence security services from FortiGuard labs to deliver top-rated protection and high performance, including encrypted traffic.
slautenschlager
Article Id 192560

Description


This article describes the first steps to troubleshoot connectivity problems to or through a FortiGate.

It is also helpful to provide this diagnostic information to the Fortinet Technical Assistance Center when opening a ticket to address a connectivity issue.

Let's assume the following diagram:

[ PC1 ] ===   port1 [ FortiGate ] port2 ==== [ PC2]

Assumptions: PC1 and PC2 can be either local to port1 and port2 subnets, or on remote subnets routed via routers.

Scope


All FortiGates and FortiOS - NAT or Transparent mode.

Solution


Summary.
Step 1: Routing table check (in NAT mode).
Step 2: Verify is services are opened (if access to the FortiGate).
Step 3: Sniffer trace.
Step 4: Debug flow.
Step 5: Session list.

Note: On FortiGate using NP2 interfaces, the traffic might be offloaded to the hardware processor, therefore changing the analysis with a sniffer trace or a debug flow as the traffic will not be seen with this procedure. 

 

For using the sniffer and debug flow with NP2 ports, NP2 offloading must be disabled. Refer to the related article given further below.

Step 1: Routing table verification.

If the FortiGate is running in NAT mode, verify that all desired routes are in the routing table: local subnets, default routes, specific static routes, and dynamic routing protocol.

 

The FortiGate will drop packets in case of RPF check failure (see related article at the end of this page Details about RPF (Reverse Path Forwarding), also called Anti Spoofing, on FortiOS ).

To verify the routing table, use the CLI command 'get router info routing-table all' as per the example below:

 

get router info routing-table all

Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
       O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default

S*      0.0.0.0/0 [10/0] via 192.168.183.254, port1, [0/50]
C       10.0.0.0/24 is directly connected, VLAN_on_port1
C       10.160.0.0/23 is directly connected, port2
C       12.0.0.0/24 is directly connected, port1
C       172.16.78.0/24 is directly connected, VLAN_on_port3
C       192.168.182.0/23 is directly connected, port1

 

To check all routes including inactive routes, use the CLI command 'get router info routing-table database'.

 

Step 2: Verify if services are opened on the port (if accessing the FortiGate itself).

 

  1. Verify that all appropriate services are opened on the interface that is being accessed. (telnet, http...)

    Example :

 

show system interface port1
    config system interface
        edit "port1"
            set vdom "root"
            set ip 192.168.182.108 255.255.254.0
            set allowaccess ping https ssh http telnet
            set type physical
        next
end

 

  1. If the interface is accessed via another port of the FortiGate, a firewall policy must exist to allow this traffic

    Example :

     

    config firewall policy
        edit 1
            set srcintf "port1"
            set dstintf "port2"
            set srcaddr "all"
            set dstaddr "all"
            set action accept
            set schedule "always"
            set service "ANY"
        next

     

Step 3: Sniffer trace.

Take a sniffer trace as per the following examples when running a constant ping (or TCP connection) from PC1 to PC2.


This will answer the following questions:

 

  • Is traffic arriving at the FortiGate and does it arrive at the expected port?
  • Is the ARP resolution correct for the targeted next-hop?
  • Is the traffic exiting the FortiGate to the destination?
  • Is the traffic sent back to the source?

 

diagnose sniffer packet any "host <PC1> and host <PC2>" 4

or

diagnose sniffer packet any "(host <PC1> and host <PC2>) and icmp" 4

 

Including the ARP protocol in the filter may be useful to troubleshoot a failure in the ARP resolution (for instance PC2 may be down and not responding to the FortiGate ARP requests).

 

diagnose sniffer packet any "host <PC1> and host <PC2> or arp" 4

 

To stop the sniffer, type CTRL+C.

With verbosity 4 above, the sniffer trace will display the port names where traffic ingresses/egresses.

Step 4: Debug flow.

Traffic should come in and leave the FortiGate. If not, proceed with a debug flow as follows:

 

diag debug enable

diag debug flow filter           <- Find the options to filter below.
diag debug console timestamp enable
diag debug flow show iprope enable

diag debug flow show function-name enable
diag debug flow trace start 100  <- This will display 100 packets for this flow.
diag debug enable

 

To stop all other debug, type 'diag debug flow trace stop'. To clear the filter, type 'diag debug flow filter clear' .

The debug filter:

 

  1. Filter based on Protocol:

 

diagnose debug flow filter proto 1

 

Proto can be changed to be another protocol number value to focus on each protocol number as follows (proto = protocol number):

protocol number 1 = ICMP (ping).
protocol number 6 = TCP.
protocol number 17 = UDP.
etc.

    1. Filter only ping that relates to the IP address that wanted to focus on.

 

diagnose debug flow filter addr x.x.x.x
diagnose debug flow filter proto 1

 

Note: x.x.x.x is the IP address that we want to filter. proto 1 is ping traffic (ICMP).

These can also be adjusted for 2 IP addresses or IP address ranges:

 

diagnose debug flow filter addr x.x.x.x y.y.y.y and / or
diagnose debug flow filter proto 1

 

The added 'and' will only show packets for ICMP between x.x.x.x and y.y.y.y, 'or' will show ICMP sourced or destined from both IP Addresses.

 

diagnose debug flow filter addr x.x.x.x y.y.y.y
diagnose debug flow filter proto 1

 

Without the boolean 'and' / 'or' this will show anything in the range between x.x.x.x and y.y.y.y:

Example:

 

diagnose debug flow filter addr 10.0.0.1 10.0.0.254
diagnose debug flow filter proto 1
diagnose debug flow filter ?
 vf: any
        proto: 1-1
        host addr: 10.0.0.1-10.0.0.254
        Host saddr: any
        Host daddr: any
        port: any
        sport: any
        dport: any

 

  1. Filter only port number.

     

    diagnose debug flow filter port Y

    Y = port number (such as 80 (http) ,25(smtp) )

     

     

  2. Filter only IP address and port number.

     

    diagnose debug flow filter addr x.x.x.x
    diagnose debug flow filter port 80

     

     

  3. Filter only source or destination port.

     

    diagnose debug flow filter sport 80 <-- Filter with the source port 80.

     

    Or:

     

    diagnose debug flow filter dport 25 <-- Filter with the destination port 25.

     

     

  4. Filter only the source IP address or destination IP address.

     

    diagnose debug flow filter saddr x.x.x.x <- Filter with the source IP address x.x.x.x.

     

    Or:

     

    diagnose debug flow filter daddr y.y.y.y <- Filter with the destination IP address y.y.y.y.

     

     

  5. Filter only the specific virtual domain.

     

    diagnose debug flow filter vd X <- 'X' is the index of the virtual domain.


    Examples of results that may be obtained from a debug flow :

    The following is an example of debug flow output for traffic that has no matching Firewall Policy, hence blocked by the FortiGate.

     

    id=20085 trace_id=319 func=resolve_ip_tuple_fast line=2825 msg="vd-root received a packet(proto=6, 192.168.129.136:2854->192.168.96.153:1863) from port3."
    id=20085 trace_id=319 func=resolve_ip_tuple line=2924 msg="allocate a new session-013004ac"
    id=20085 trace_id=319 func=vf_ip4_route_input line=1597 msg="find a route: gw-192.168.150.129 via port1"
    id=20085 trace_id=319 func=fw_forward_handler line=248 msg=" Denied by forward policy check"

     

    The following is an example of debug flow output for traffic going into an IPSec tunnel in Policy-based. This is a working scenario.

     

    See traffic is matching and processed by Firewall Policy #2.

     

    id=20085 trace_id=1 msg="vd-root received a packet (proto=1, 10.72.55.240:1->10.71.55.10:8) from internal."
    id=20085 trace_id=1 msg="allocate a new session-00001cd3"
    id=20085 trace_id=1 msg="find a route: gw-192.168.56.230 via wan1"
    id=20085 trace_id=1 msg="Allowed by Policy-2: encrypt"
    id=20085 trace_id=1 msg="enter IPsec tunnel-RemotePhase1"
    id=20085 trace_id=1 msg="encrypted, and send to 192.168.225.22 with source 192.168.56.226"
    id=20085 trace_id=1 msg="send to 192.168.56.230 via intf-wan1“
    id=20085 trace_id=2 msg="vd-root received a packet (proto=1, 10.72.55.240:1-10.71.55.10:8) from internal."
    id=20085 trace_id=2 msg="Find an existing session, id-00001cd3, original direction"
    id=20085 trace_id=2 msg="enter IPsec ="encrypted, and send to 192.168.225.22 with source 192.168.56.226“ tunnel-RemotePhase1"
    id=20085 trace_id=2 msgid=20085 trace_id=2 msg="send to 192.168.56.230 via intf-wan1"

     

    Other information messages are explained in the article 'Troubleshooting Tip: debug flow messages 'iprope_in_check() check failed, drop' - 'Denied by forward policy check' - 'reverse path check fail, drop'.

Step 5: Session list.

One further step is to look at the firewall session. For this, some filters may be used to reduce the output; see the following example:

 

diag sys session filter src PC1
diag sys session list

 

Or:

 

diag sys session filter dst PC1
diag sys session list

 

The analysis of the output of this command is further detailed in the related article below (FortiGate Firewall session list information).

To clear all sessions corresponding to a filter:

 

diag sys session filter dst PC1
diag sys session clear

 

 

Related articles:

Troubleshooting Tool: Using the FortiOS built-in packet sniffer

Troubleshooting Tip: FortiGate session table information

Troubleshooting Tip : How to use the FortiGate sniffer and debug flow in presence of NP2 ports

Technical Note: Configuration best practice and troubleshooting tips for a FortiGate in Transparent ...

Technical Note: Details about FortiOS RPF (Reverse Path Forwarding), also called Anti-Spoofing

Troubleshooting Tip : debug flow messages 'iprope_in_check() check failed, drop' - 'Denied by forwar...

Troubleshooting Tip : Message msg='HWaddr-xx:xx:xx:xx:xx:xx is in black list, drop' in a 'diagnose d...