Troubleshooting Tip: How to fix 'SSL connection is...

esalija · 09-17-2025

Description This article describes the process of configuring SSL traffic mirroring with a focus on modifying the Destination MAC address at the policy level, allowing administrators to accurately duplicate SSL traffic for analysis or inspection. Sco...

esalija · 08-18-2025

Description This article describes the configuration side of the Automation Stitch when Multiple Link Monitors are implemented and receive an email for a specific Link monitor change. Scope FortiGate. Solution When one of the link monitors goes down ...

esalija · 07-16-2025

Description This article describes how to work around the error code -23 when trying to change the http-incoming-port to 8000. Scope FortiGate, FortiProxy. Solution When trying to change the http-incoming-port 8000, the following error will be encoun...

esalija · 06-18-2025

Description This article describes the error https:-2 - Must set at least one port for HTTP3(QUIC) when trying to install a security policy from FortiManager to the FortiGate. Scope FortiManager, FortiGate. Solution While trying to install a firewall...

esalija · 05-16-2025

Description This article describes the error code -23 case while deleting a custom ISDB. Scope FortiGate. Solution When trying to remove an entry in an 'internet-service-custom' object, it fails with the following error: config firewall internet-serv...

esalija · 09-06-2025

Hi @Gianluca1 FortiClient is not specifically designed for installation on hypervisors. It is intended for use on the following devices and operating systems: 1. Microsoft Windows 7, 8, 8.1, 10, and 11 (both 32-bit and 64-bit where applicable). 2. Wi...

esalija · 09-06-2025

Hi @joh, To set up logging for outbound LAN traffic on your FortiGate 60F and store logs on a USB device, follow these steps: 1. Enable Logging for Outbound Traffic- Go to the FortiGate web interface.- Navigate to Log & Report > Log Settings.- Ensure...

esalija · 07-23-2025

Hi @AlexFerenX , Yes, the values and explanation are general networking concepts. Best regards, Erlin

esalija · 07-21-2025

HI @AlexFerenX The explanation provided for scope values is more aligned with general networking concepts and Linux-based systems rather than being FortiOS-specific. Best regards, Erlin

esalija · 07-21-2025

Hi @AlexFerenX In the context of Kernel routing tables, the "scope" value indicates the reachability of a route. - A "scope" value of 0 indicates a global route. This means the route is valid for the entire network and can be used to route traffic be...

User Statistics

User Activity

Technical Tip: Change the destination MAC address for Mirror SSL traffic

Technical Tip: Receive an email for a Link Monitor when Multiple Link monitor are configured in an automation stitch

Technical Tip: How to use port 8000 for explicit proxy on FortiGate/FortiProxy

Troubleshooting Tip: How to fix 'error https - :-2 - Must set at least one port for HTTP3(QUIC)"

Technical Tip: Error code -23 when deleting Custom Internet Service DataBase (ISDB)

Re: About FortiClient

Re: How to set full log. Better on USB device

Re: Meaning and significance of "scope" in FIB printouts?

Re: Meaning and significance of "scope" in FIB printouts?

Re: Meaning and significance of "scope" in FIB printouts?

Troubleshooting Tip: How to fix 'SSL connection is...

Technical Tip: High CPU usage is triggered from IP...

Technical Tip: How to perform multiple certificate...

Technical Tip: Configure a new policy with an Auto...

Technical Tip: The HA Cluster license requirements

Re: Fortigate Evaluation License Offline Mode

Re: interface down!

Re: Is there any difference between the fortiguard...

Re: Fortiguard SSL gateways

Re: Flow based or proxy based

KCS

User Statistics

User Activity

You are leaving our website