Troubleshooting Tip: How to find the device respon...

ssudhakar · 10-25-2023

Description This article outlines a method for identifying the device causing fragmentation through a ping test. However, this approach may not always be possible, especially when access to all devices along the network path is limited. Scope All sup...

ssudhakar · 05-24-2022

Description This article describes how to troubleshoot if the blades on the chassis are stuck at 'Waiting for data heartbeat' status in a HA cluster. Scope FortiGate 6000/7000 series , v5.6, v6.0,v6.2,v6.4. Solution From ' diag load-balance status', ...

ssudhakar · 01-05-2022

Description This article describes the changes in the IPSec load-balance setting from v6.2.6/6.4.6 onwards. IPSec load-balancing is enabled on FortiGate 6000 series and disabled on FortiGate 7000 series by default until v6.2.4/v6.4.2 and this config ...

ssudhakar · 04-16-2021

DescriptionThis article describes the changes in the inspection mode In policies and UTM profiles from version 6.0 to 6.2.SolutionIn 6.0 version.- The inspection mode is set per VDOM.- UTM profiles can be set in flow or proxy mode.- When applying the...

ssudhakar · 04-15-2021

DescriptionFrom '# diagnose load-balance status' if any blade are stuck at 'waiting for configuration sync' status or from '# diagnose sys configsync status' if in_sync=0, then it means that there is a config mismatch. This article describes how to f...

ssudhakar · 04-11-2024

Hello there: "Failed to connect to FWB device" error message occurs when FortiwebManager cannot SSH connect the fortiweb device Can you please check these ? 1/ port22 is allowed inbound in fortiweb device's security group; 2/ the FortiwebManager's IP...

ssudhakar · 04-11-2024

Hello there : The duplication works only in original direction. https://community.fortinet.com/t5/FortiGate/Technical-Tip-Packet-duplication-in-SD-WAN/ta-p/258997 Hope that helps!

ssudhakar · 01-02-2024

Hello there:Yes, you can . Here are few KBs with detailed explanation : The conditions for configuring HA are as follows: Devices must be of the same model. Devices must have the same Firmware version. The same licenses must be applied to all devices...

ssudhakar · 01-02-2024

Hello there: You can try configuring a DOS policy . It generates a log when there is an attack . Few KBs are here:https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-configure-IPv4-DOS-policy/ta-p/189653https://community.fortinet.com/t5/...

ssudhakar · 07-29-2022

Hi there : Below is a cookbook which explains FMG-Access https://docs.fortinet.com/document/fortigate/6.2.0/cookbook/574723/interface-settings FMG-Access Allow FortiManager authorization automatically during the communication exchanges between FortiM...

User Statistics

User Activity

Troubleshooting Tip: How to find the device responsible for fragmentation along the network path

Technical Tip : FPC/FPMs stuck at 'Waiting for data heartbeat'

Technical Tip: 'IPSec load-balance setting changes after upgrading to v6.2.6/6.4.6 onwards'

Technical Tip: Change in inspection mode - Flow vs Proxy policy option after upgrade to 6.2

Technical Tip: How to find the config difference between blades in 6K/7K Chassis using 'diagnose sys confsync diffcsum' command

Re: Fortiweb Manager - add Device

Re: Packet duplication not done in session return packets

Re: FortiGate question

Re: DDOS Questions Fortigate

Re: FMG-Access? What Is It?

Troubleshooting Tip: How to find the device respon...

Re: FMG-Access? What Is It?

Re: Hide FortiClient Main Window on Windows Startu...

Re: How to Edit Email Alert Settings

Re: How to Edit Email Alert Settings

Re: Packet duplication not done in session return ...

Re: FMG-Access? What Is It?

Re: How to Edit Email Alert Settings

Re: How I do backup for FortiSIEM?

KCS