Fortinet Community

slautenschlager · 09-02-2021

DescriptionThis article describes how to connect to a FortiEMS over an IPsec VPN tunnel.SolutionLet’s assume that the site-to-site IPSEC VPN tunnel is up and the traffic can pass through just fine.1) Adding the Forticlient EMS.Go to Security Fabric -...

slautenschlager · 08-29-2019

Description This article describes how to use the built-in packet capture feature in FortiOS from the GUI interface.Solution On the 5.6 firmware branch, the unit needs a disk and logging to disk has to be enabled.Since the firmware version 6.0.2, thi...

slautenschlager · 08-27-2019

Description This article describes how to recover trial FortiToken Mobile serial numbers in later FortiOS versions. If there were deleted from the firewall, then the free service cannot be used.FortiGate firewalls are shipped with two free FortiToken...

slautenschlager · 08-20-2019

DescriptionThis article explains how to enable and disable the FortiGate system session helper.ScopeFortiGate units, running FortiOS versions 5.4, 5.6, 6.0 and 6.2SolutionAs outlined in the FortiGate CLI Reference Guide, a session helper binds a serv...

slautenschlager · 08-05-2016

DescriptionThe list of unit models supported by FortiAnalyzer and FortiManager is documented in the release notes. Alternatively, there is a CLI command that can be used to obtain this information.SolutionOpen the CLI console in FortiAnalyzer or Fort...

slautenschlager · 04-18-2023

Hi ck, hard to tell with this explanation without seeing your configuration. Can you see session clashes in your logs that basically the same natted source port is used? But as you are using different snat ippools might not be the issue. I would reco...

slautenschlager · 06-29-2022

Hi Patrick, I had a few cases for this and all feedback I received was, that it was working after the upgrade. Let's see if it happens again. In this case I would suggest to raise a ticket for further analysis, Best , Steffen

slautenschlager · 06-08-2022

Dear Kenneth,   yes this issue is fixed in 7.0.6   Best , Steffen

slautenschlager · 03-10-2022

Dear Jomof, it might need to check with configuration of Switch and Fortigate, so it might be better to raise a TAC case with the serial number of the Fortiswitch to check this a little bit deeper. Best, Steffen

slautenschlager · 03-10-2022

Dear Jomof, it may be, that the FortiSwitch OS is not compatible to your actual FortiOS for the Fortilink - please refer to the attached compatibility matrix :https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/d756e8a9-6d2d-11e9-81...

Fortinet Community

User Statistics

User Activity

Technical Tip: Enable Communication to FortiEMS from the Fortigate through an IPsec VPN tunnel

Troubleshooting Tip: Packet Capture on FortiOS GUI

Technical Tip: How to recover trial FortiToken Mobile serial numbers

Technical Tip: Enable and disable FortiGate system session helpers

Technical Tip: How to check the units supported by FortiManager and FortiAnalyzer

Re: How do the VIP address are source natted and the purpose to bind a VIP to an Interface

Re: FG-61F: "FortiSwitch Ports" does not show devices anymore in column "Device Infor

Re: FG-61F: "FortiSwitch Ports" does not show devices anymore in column "Device Infor

Re: Fortiswitch is showing offline when fortigate connect via fortlink

Re: Fortiswitch is showing offline when fortigate connect via fortlink

Technical Tip: Technical support on customization ...

Re: FG-61F: "FortiSwitch Ports" does not show devi...

Troubleshooting Tip: Packet Capture on FortiOS GUI

Troubleshooting Tip: First steps to troubleshoot c...

Re: FG-61F: "FortiSwitch Ports" does not show devi...

KCS