Technical Tip: Details about host check list and ...

nithincs · 07-31-2023

Description This article provides the CLI commands to renew/reconnect the DHCP/PPPoE connection of the WAN interface. Scope FortiGate. Solution The FortiGate interface can be configured as a DHCP client or PPPoE client to fetch the IP dynamically. In...

nithincs · 07-18-2023

Description This article describes how to use FortiGate as an SSH client to log in and access another host device. Scope FortiGate. Solution Login to the FortiGate CLI console or through Putty using SSH or Telnet. Use the below command syntax to log ...

nithincs · 07-14-2023

Description This article describes to read the cause of an HA failover from the output of the 'get sys ha status' command. Scope Any supported version of FortiGate. Solution Executing "get sys ha status" in any ha cluster member will provide the fail...

nithincs · 06-14-2023

Description This article describes the background of DHCP message exchange and explains the root cause of the DHCP debug message 'There is no requesting IP in subnet!' Scope FortiGate. Solution While debugging the DHCP service running in the firewall...

nithincs · 06-12-2023

Description This article describes the background of DHCP message exchange and explains the root cause of the DHCP status 'Removed due to conflict'. Scope FortiGate. Solution After completing the DORA process and getting the IP from the DHCP server, ...

nithincs · 07-24-2023

yes, you could achieve it. Make sure to add dailup tunnel subnet in phase2 selector of the site-site tunnel. in FGT1 source :10.5.41.0/24 dest :192.168.8.0/24in FGT2 source 192.168.8.0 dest :10.5.41.0/24 In FGT2, add a routeto 10.5.41.0 via tunnel in...

nithincs · 05-22-2023

Hi Imel, I believe, you need to create ip pools for each nat ip address. Later call the same in specific soucre and destination policy. Please refer to https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-configure-SNAT-with-IP-pool/ta-p/...

nithincs · 05-22-2023

hi, the script is correct. You can also follow alert mail for concerve mode and logs collection https://community.fortinet.com/t5/FortiGate/Technical-Tip-Automation-stitch-for-the-conserve-mode/ta-p/240696#:~:text=FortiGate%20by%20default%20turns%20o...

nithincs · 05-08-2023

hi Abel,Please make sure you have spit tunnel enable in the sslvpn so you that only remote subnet are pointing todards sslvpn adaptor in local pc. Better to check routing-table in the pc before and after connecting to sslvpn. use "route print" if its...

nithincs · 08-23-2022

Hi, Please try the solution provided in https://community.fortinet.com/t5/FortiGate/Technical-Tip-Error-The-VPN-server-may-be-unreachable-14-for/ta-p/190882

User Statistics

User Activity

Technical Tip: CLI commands to renew the DHCP and PPPoE connection

Technical Tip: How to take the SSH access of the other host from FortiGate device

Technical Tip: Understading FortiGate HA failover causes from HA status output

Troubleshooting Tip: DHCP debug message 'There is no requesting IP in subnet!'

Troubleshooting Tip: DHCP status 'Removed due to conflict'

Re: Can remote FortiClient user get access to local lan connected over syte-2-syte tunnel?

Re: Dynamic NAT

Re: Restart Fortigate http/gui processes automatically because of a memory leakage

Re: Printer behind FortiClient not accessible

Re: FortiClient VPN connection error (-14)

Technical Tip: Details about host check list and ...

Troubleshooting Tip: Not able to ping the Ipsec VP...

Technical Tip: Automation stitch for the admin log...

Technical Tip: FAQs regarding virtual wire pairs

Re: FortiClient VPN connection error (-14)

Fortinet Training Institute

KCS