Technical Tip: FortiAP rolls back to old firmware ...

manasac · 10-21-2022

Description This article describes how to fix an issue where the Virtual Controller reboots every hour. Scope Wireless Controllers. Solution This issue occurs if the IP address on the Virtual Controller changes, which causes the system ID to change. ...

manasac · 10-20-2022

Description This article describes how to identify and fix the cause of a high channel utilization being reported on FortiAP (Managed by FortiGate) Scope FortiGate, FortiAP-U, FortiAP-W2 Solution Identify the device causing interference and take the ...

manasac · 09-05-2022

Description This article descibes when the FortiGate management status on FortiWLM inventory is 'INACTIVE'. Adding FortiGate on FortiWLM Inventory is not successful. Scope FortiGate management status on FortiWLM should be ACTIVE to push config and lo...

manasac · 09-05-2022

Description This article describes how FortiAP rolls back to old firmware even after successful upgrade attempt. Scope FortiGate, FortiAP, Upgrade, Firmware Solution Delete the old FortiAP firmware from the image list on FortiGate Commands to check a...

manasac · 01-05-2021

DescriptionThis article describes how to configure Management VLAN for FortiAP-C24J.ScopeFor FortiAP-C24J.SolutionNote: The VLAN from which FortiAP should receive IP address should be configured in tagged VLAN list on the up link switch where FortiAP...

manasac · 01-18-2023

Hi @Spoil-Equation To answer your question, I need to know the network diagram. You have mentioned about the wired device, I need to know how are they connected ? are they connected directly to FGT or any of the 3rd party switches and then to FGT? It...

manasac · 01-18-2023

Hi @Spoil-Equation The Fortilink interface type is aggregated, both the ports on the aggregated interface should be connected to Fortiswitch. Connecting FAP to one of the ports is not supported. Hardware switch interface type will support connecting ...

manasac · 12-23-2022

Hi @bogdanbugher Please go through below link for more information on the list of switches that supports split ports and commands https://docs.fortinet.com/document/fortiswitch/6.4.2/administration-guide/861224/physical-port-settings#Configur4

manasac · 11-08-2022

Hi @amguirado73 >Connect a test client to port 10 After connecting the client on port 10 , execute below command and share the output here to check the STP status, log display and if there is any crash reported #diag debug report

manasac · 11-05-2022

Hi @shogechi restore Use the above command to upgrade AP via CLI. Please let me know if this helps.

User Statistics

User Activity

Troubleshooting Tip: Fix the controller constantly rebooting every hour

Troubleshooting Tip: Channel utilization is reported high on FortiAP (Managed by FortiGate)

Technical Tip: FortiGate status on FortiWLM inventory is 'Online INACTIVE'

Technical Tip: FortiAP rolls back to old firmware even after successful upgrade attempt

Technical Tip: How to configure management VLAN for FortiAP-C24J

Re: VLAN issue on FG-80F with FAP-433F and SW-108-FPOE

Re: VLAN issue on FG-80F with FAP-433F and SW-108-FPOE

Re: Fortiswitch T1024E

Re: Ports supplying PoE but not linking

Re: Fortiap 221c UI failing to login

Technical Tip: FortiAP rolls back to old firmware ...

Technical Tip: FortiLink interface is not listed u...

Re: VLAN issue on FG-80F with FAP-433F and SW-108-...

Re: Wireless issue. Deny assoc request, ht rate se...

Re: Reset Admin password

Re: Wireless issue. Deny assoc request, ht rate se...

Fortinet Training Institute

KCS