Technical Tip : BGP Routing process when 'Soft Rec...

darisandy · 01-21-2026

Description This article describes how to troubleshoot one way SIP Audio issue on the agent over an SSL VPN Tunnel. Scope FortiGate. Solution Scenario : SIP-ALG is enabled: config system settings set default-voip-alg-mode proxy-based end Split Tunnel...

darisandy · 12-07-2025

Description This article describes how to configure FortiAuthenticator as a TACACS+ Client. Scope FortiAuthenticator v6.6.x. Solution Admin access into FortiAuthenticator can be configured to use the TACACS+ Server user database. FortiAuthenticator d...

darisandy · 12-04-2025

Description This article describes the steps to troubleshoot OSPF issues between FortiGate and Palo Alto devices when MD5 authentication is enabled for neighborship. Scope FortiGate. Solution OSPF MD5 authentication needs to be enabled per interface....

darisandy · 11-24-2025

Description This article describes how to troubleshoot when the BGP attribute is not getting applied after a configuration change. Scope FortiGate. Solution BGP Scenario: FGT-01 --- 2 links (port2 and port3) --- FGT-02. FGT-02 is advertising 2 subnet...

darisandy · 10-08-2025

Description This article describes the behavior of the TACACS packet on FortiGate HA Cluster depending on the ha-direct option. Scope FortiGate HA Cluster. Solution When 'ha-direct is enabled, each FortiGate unit will initiate the TACACS connection f...

darisandy · 12-07-2023

The numbers on datasheet was done on lab environment and those are only a benchmark of what the hardware could possibly handle. But I believe only Fortigate product team know exactly how the test was done. For any capacity planning enquiries, I would...

darisandy · 12-07-2023

you can create VLAN interface (tagged interface) under that one physical interface https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-create-a-VLAN-tagged-interface-802-1q-on-a/ta-p/193893 after that you can specify the default route,wh...

darisandy · 12-07-2023

few articles you can read up about it : https://community.fortinet.com/t5/Support-Forum/why-do-we-assign-secondary-IP-address/m-p/219857 https://community.fortinet.com/t5/FortiGate/Technical-Tip-Set-a-secondary-IP-on-a-FortiGate-interface/ta-p/226046

darisandy · 12-03-2023

Based on the available command you shared, I don't think it's possible. Once the ports are member of LACP interface, most likely that older version can't refer to the physical port anymore.

darisandy · 12-03-2023

It's a bit tricky to set management access on FGT Transparent Mode. You may want to check docs send by Minh for more detailed deployment. Usually when you have multiple VLAN going through FGT, you need to define forward domain. So the traffic will no...

User Statistics

User Activity

Troubleshooting Tip: One way audio issue on agent over SSL VPN tunnel

Technical Tip : How to Configure FortiAuthenticator as TACACS+ Client

Troubleshooting Tip : OSPF not established between FortiGate and Palo Alto device when MD5 authentication enabled

Troubleshooting Tip: BGP Attribute was not being applied after the change

Technical Tip : TACACS difference behavior when ha-direct enable or disabled

Re: FG-60F Performance Questions

Re: Two ISPs different VLAN

Re: Fortigate Interface settings

Re: problem with HA monitored interface configuration for LACP interface

Re: About management IP settings in transparent mode

Technical Tip : BGP Routing process when 'Soft Rec...

Technical Tip: How to block SSL VPN Connection fro...

Re: Remote RADIUS Server on a VPN

Technical Tip : Behaviour Change of SD-WAN Member ...

Technical Tip : Cyber-bullying and social media us...

Re: Source Nat with destination port

Re: Integration of Fortigate with Zabbix

KCS

User Statistics

User Activity

You are leaving our website