Fortinet Community

sachitdas_FTNT · 09-13-2023

Description This article describes the troubleshooting steps to check when IGMP snooping is not working as expected. Scope FortiSwitch v6.4.x and above. Solution Before beginning, it is important to go through the below links, it contains important i...

sachitdas_FTNT · 09-05-2023

Description This article describes how to restore a FortiSwitch after an RMA. Scope FortiSwitch v6.4.x and above. Solution Upgrade the FortiSwitch from the GUI. Depending on the FortiSwitch, there may be a dedicated management port with an IP address...

sachitdas_FTNT · 08-29-2023

Description This article describes what to do when it is not possible to access FortiSwitch GUI using HTTP or HTTPS. Scope FortiSwitch v7.0.x and v7.2.x. Solution Follow these steps if it is not possible to access the FortiSwitch GUI despite the corr...

sachitdas_FTNT · 06-02-2023

Description This article describes how to consider if FortiSwitch's internal interface native VLAN changes to a different VLAN after the switch reboot Scope FortiSwitch v7.2.x and above. Solution Starting from FortiSwitch 7.2.0, 'auto-network' featur...

sachitdas_FTNT · 06-01-2023

Description This article describes how to fix an error seen on FortiSwitch logs: 'failed DIAG-CONTROL Check Sequence'. Scope FortiSwitch version 6.4.x and above. Solution If the SFP ports repeatedly go 'Up' and 'Down' due to the error 'failed DIAG-CO...

sachitdas_FTNT · 08-17-2023

Yes thats correct, you need to configure the native and allowed vlans on port24

sachitdas_FTNT · 08-17-2023

Hope this helps: https://community.fortinet.com/t5/FortiSwitch/Troubleshooting-Tip-Configure-IP-parameters-on-out-of-box/ta-p/194869 In FSW version 7.2 and above, we have "auto-network" configuration, so if you are using standalone mode, then we shou...

sachitdas_FTNT · 01-03-2023

Hi, From what I understand is the issue specific to Macbook? Do other devices like windows laptops also witness the same problem?

sachitdas_FTNT · 09-27-2022

Hi Imran, Please upgrade FSW to latest version 7.0.5, dhcp server on fsw is supported from later versions.

sachitdas_FTNT · 09-23-2022

We can enable below options from fgt on the vlan interface. FortiGate-300D # config system interface FortiGate-300D (interface) # edit vlan10 FortiGate-300D (vlan10) # set switch-controller-igmp-snooping enable FortiGate-300D (vlan10) # set switch-co...

Fortinet Community

User Statistics

User Activity

Troubleshooting Tip: IGMP Snooping not working on FortiSwitch

Technical Tip: How to restore a FortiSwitch (FSW) appliance after RMA

Technical Tip: HTTP/HTTPS to FortiSwitch not working

Troubleshooting Tip: Internal interface native VLAN changes after switch reboot

Troubleshooting Tip: Failed DIAG-CONTROL check sequence

Re: Connect Fortiswitch (standalone mode) to a cisco 3850

Re: Connect Fortiswitch (standalone mode) to a cisco 3850

Re: FortiSwitch: Spanning Tree Issue - Port disabled

Re: FS1E48 || v6.0.1,build0036,180727 (GA) || DHCP option

Re: IGMP SNOOPING configuration getting erased.

Re: Cisco breakout DAC on FortiSwitch

Re: Wireless Client Isolation

Re: Question: two Vdom vlans to the same port ( na...

Re: How to set up FG 40F to manage two independent...

Re: How to set up FG 40F to manage two independent...

Re: Fortiswitch fs-148e-poe SFP or SFP+ Ports?

Re: Fortilink across L3 (FG-FSW only)

Re: Question: two Vdom vlans to the same port ( na...

Re: Fortiswitch ports not showing - blank page

KCS

Fortinet Training Institute