Troubleshooting Tip: FortiOS to AWS VPN Anti-Spoof...

Jackie_T · 11-02-2025

Description This article describes how to resolve the FortiPAM GNOME RDP issue. The issue occurs when attempting to access a GNOME RDP server through FortiPAM, resulting in a failed connection. Scope FortiPAM. Solution GNOME RDP is supported by Forti...

Jackie_T · 10-09-2025

Description This article describes the steps to identify the approver of a secret request in FortiPAM and the known issue with approval process through email. Scope FortiPAM Solution To identify the approver of a secret request in FortiPAM, follow th...

Jackie_T · 10-05-2025

Description This article describes the issue of being unable to change the password for a Windows local user. The error message 'Password change failed (SAMR connection to machine failed. Error was NT_STATUS_ACCESS_DENIED, but LANMAN password changes...

Jackie_T · 09-03-2025

Description This article describes how to set up push notifications for FortiToken Mobile in FortiPAM. Scope FortiPAM v1.5.x, v1.6.x, v1.7.x. Solution Set up Topology: In the above setup, there is a firewall between FortiPAM and the internet. Configu...

Jackie_T · 09-03-2025

Description This article describes the steps to enable the PAM debug logs on FortiClient, which is disabled by default. Scope FortiClient with FortiPAM enabled. Solution FortiPAM with FortiClient relies on FortiVRS for video recording. For more infor...

Jackie_T · 09-30-2024

Hi, For simple setup, you can achieve this by configure ECMP routes.Mean both WAN1 and WAN2 will have same distance value set, but WAN1 will have higher priority value set.The link with higher priority value will be less preferred and stay as standby...

Jackie_T · 09-11-2024

Hello HS08, I believe you are looking for the default value for ospf cost bandwidth reference in FortiOS? There is a setting under "config router ospf" >> "set auto-cost-ref-bandwidth". The default value set is 1000, in megabits per second. Reference...

Jackie_T · 08-26-2024

Hi Shane, Yes, is top-down rule.If you have multiple vlans, I believe you already configure trunk to allow those vlans on the switch? You might want to check below:1. Ensure routing is configure correctly:#get router info routing-table allYou should ...

Jackie_T · 08-26-2024

Hi forsenGa, There is a KB as well for this:https://community.fortinet.com/t5/FortiGate/Technical-Tip-Authentication-fails-with-clock-skew-errors-in/ta-p/222360 Thanks.

Jackie_T · 08-26-2024

Hi Alan, Transparent mode (Layer 2 deployment) is for a deployment where you need to integrate the FortiGate into an existing network without changing the IP structure, while still allowing for security policies.Transparent mode does not perform NAT ...

User Statistics

User Activity

Troubleshooting Tip: FortiPAM GNOME RDP Issue

Technical Tip: FortiPAM identify approver for secret approval

Troubleshooting Tip: Cannot Change Password for Windows Local User

Technical Tip: FortiPAM FortiToken Mobile push notification setup

Technical Tip: FortiPAM enable FortiVRS debug logs on FortiClient

Re: Need assistance - dual WAN

Re: OSPF Cost

Re: Fortigate 201F 7.6.0 LAN -> WAN ALL/ALL not working

Re: SAML clock skew issue

Re: Transparent mode

Troubleshooting Tip: FortiOS to AWS VPN Anti-Spoof...

Technical Tip: FortiGate Disable Hardware Accelera...

Troubleshooting Tip: NPU Info Flag Field in FortiO...

Technical Tip: FortiGate monitoring script

Technical Tip: Compatibilities of Hardware Switch ...

Re: How to increase (expand?) disk space

KCS

User Statistics

User Activity

You are leaving our website