Re: Multicast policy

Benoit_Rech_FTNT · 10-31-2013

Description This article describes the reasons behind multicast packets being unable to traverse the FortiGate unit, despite the presence of a static route configured to utilize a VRRP, HSRP, or GLBP address for reaching a PIM sparse-mode RP. Scope F...

Benoit_Rech_FTNT · 10-04-2012

Description This article describes why the FortiGate answers to traceroute on the VIP addresses despite how traceroute traffic is not allowed by the firewall policies. Scope Firewall VIP, and traceroute. Solution Diagram: Expectations, Requirements: ...

Benoit_Rech_FTNT · 10-03-2012

Description This article provides a solution to use Policy Based Routing (PbR) on traffic managed by the web-proxy of the FortiGate.When you enable explicit proxy of the FortiGate, the concerned traffic is "proxied" on the FortiGate. That is to say t...

Benoit_Rech_FTNT · 09-19-2012

Purpose The purpose of this article is to explain how to backup the FortiGate Configuration with Kiwi CatTools, starting with FortiOS 4.0 MR3 Patch11 (4.2.11) and FortiOS 4.0 MR3 Patch4 (4.3.4). Scope Starting from FortiOS 4.0 MR2 Patch11 (4.2.11) an...

Benoit_Rech_FTNT · 08-28-2012

Purpose Configure the FortiGate to synchronize its clock to a different time server, and secure the NTP update using MD5 authentication.NTP protocol:NTP stands for Network Time Protocol. It is used to synchronize the time of a computer to reference N...

Benoit_Rech_FTNT · 09-29-2021

Hello,it could be interesting to know the reason of the "closure". You can get the information from "get router info bgp neighbors xx.xx.xx.xx" where xx.xx.xx.xx is the IP address of the peer. You can also get the status of the connection using 'get ...

Benoit_Rech_FTNT · 09-28-2021

Hello,Create IGMP "service":config firewall service custom edit "IGMP" set protocol IP set comment "IGMP" set protocol-number 2 nextendand then the local policyconfig firewall local-in-policy edit 0 set intf "dmz" set srcaddr "all" set dstaddr "all" ...

Benoit_Rech_FTNT · 09-27-2021

Hello,the KB shows external to internal IPs, but you can apply this KB to internal (or local) subnets. basically, it's doing static NAT between your 2 networks. But, from what you request at the beginning of the post, you need to access server B (192...

Benoit_Rech_FTNT · 09-27-2021

Hello,you can check the routing table using 'get router info routing-table all' and then confirm your assumptions.If you are not sure, copy/paste the output of the commands in the thread.Best regards Benoit

Benoit_Rech_FTNT · 09-27-2021

Hello,By default, IGMP has a TTL of 1, which means it will not be routed by the Fortigate. Moreover, IGMP is not enabled by default on the Fortigate, you have to enable it on each interface which should participate to multicast. For me, there is noth...

User Statistics

User Activity

Technical Tip: Implementing PIM Sparse Mode in a VRRP, HSRP or GLBP Configuration Environment

Troubleshooting Tip: Why the Firewall VIP responds to traceroute

Technical Tip: How to configure PBR to route explicit proxy traffic

Technical Tip : How to backup FortiGate configurations using Kiwi CatTools

Technical Tip : Configuring NTP with authentication

Re: BGP Session needs refresh

Re: Block or Disable IGMP

Re: One way pings

Re: mgmt port gw

Re: Block or Disable IGMP

Re: Multicast policy

Re: Throughput on inter vdom link

Re: OSPF Faild Dependeny Error

Re: Strange syslog for Fortigate device

Re: vlan working2

Re: One Vlan on multiple ethernet interfaces

Re: How to add static route point to PPPoE interfa...

KCS

Fortinet Training Institute

User Statistics

User Activity

You are leaving our website