config firewall address edit " all" next edit " outside.blacklist.121.139.0.0" set subnet 121.139.0.0 255.255.0.0 next edit " outside.blacklist.96.8.126.97" set subnet 96.8.126.0 255.255.255.0 next edit " outside.blacklist.108.61.91.211" set subnet 108.61.91.0 255.255.255.0 next end config firewall addrgrp edit " outside.blacklist.All" set member " outside.blacklist.96.8.126.97" " outside.blacklist.108.61.91.211" " outside.blacklist.121.139.0.0" [geography-based lists] next end config firewall policy edit 53 set srcintf " wan1" set dstintf " dmz" set srcaddr " outside.blacklist.All" set dstaddr " all" set schedule " always" set service " ALL" set logtraffic all next edit 26 set srcintf " wan1" set dstintf " dmz" set srcaddr " all" set dstaddr " nat.inbound.rounding" set action accept set schedule " always" set service " HTTP" " HTTPS" set utm-status enable set av-profile " MainAV" set ips-sensor " protect_http_server" set profile-protocol-options " default" next edit 37 set srcintf " wan1" set dstintf " dmz" set srcaddr " all" set dstaddr " nat.inbound.smtp" set action accept set schedule " always" set service " SMTP" set utm-status enable set av-profile " MainAV" set spamfilter-profile " MSPS Email Filter" set ips-sensor " protect_email_server" set profile-protocol-options " default" next edit 42 set srcintf " wan1" set dstintf " dmz" set srcaddr " all" set dstaddr " nat.inbound.owa" set action accept set schedule " always" set service " HTTPS" " HTTP" set utm-status enable set av-profile " MainAV" set ips-sensor " protect_http_server" set profile-protocol-options " default" next edit 49 set srcintf " wan1" set dstintf " dmz" set srcaddr " all" set dstaddr " nat.inbound.rdsgate" set action accept set schedule " always" set service " HTTPS" " RDS_external_UDP" set utm-status enable set av-profile " MainAV" set ips-sensor " protect_http_server" set profile-protocol-options " default" next edit 51 set srcintf " wan1" set dstintf " dmz" set srcaddr " all" set dstaddr " nat.inbound.remote" set action accept set schedule " always" set service " HTTPS" set utm-status enable set av-profile " MainAV" set ips-sensor " protect_http_server" set profile-protocol-options " default" next endThese policies have been in place for sometime, yet this morning I have had the same IP address showing up in my IPS logs quite a bit:
Message meets Alert condition The following intrusion was observed: " PHP.CGI.Argument.Injection" . date=2014-08-08 time=10:18:04 devname=fw01 devid=FGT80C3911608826 logid=0419016384 type=ips subtype=signature level=alert severity=high srcip=96.8.126.97 dstip=[DMZ address of host in policy 42 above] srcintf=" wan1" dstintf=" dmz" policyid=42 identidx=0 sessionid=13078459 status=dropped proto=6 service=http count=1 attackname=" PHP.CGI.Argument.Injection" srcport=33113 dstport=80 attackid=31752 sensor=" protect_http_server" ref=" http://www.fortinet.com/ids/VID31752" incidentserialno=513620505 msg=" web_server: PHP.CGI.Argument.Injection,"The source IP in this message is in my blacklist and I' ve tried specifying both it as a host and a /24 which included the address. Yet, inbound traffic from this host still seems to whiff past the deny policy and match against the next policy in the list instead. Any idea what I' m missing here? Any help at all is appreciated. Cheers, Rick
Solved! Go to Solution.
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
If you are trying to block countries by geo, I would do it via local-in-policy., e.g.
config system global
set gui-local-in-policy enable
end
config firewall address
edit "block-country-netherlands"
set associated-interface "wan1"
set type geography
set country "NL"
next
edit "block-country-brazil"
set associated-interface "wan1"
set type geography
set country "BR"
next
edit "block-country-lithuania"
set associated-interface "wan1"
set type geography
set country "LT"
next
edit "block-country-sweden"
set associated-interface "wan1"
set type geography
set country "SE"
next
edit "block-country-china"
set associated-interface "wan1"
set type geography
set country "CN"
next
edit "block-country-russia"
set associated-interface "wan1"
set type geography
set country "RU"
next
end
config firewall addrgrp
edit "block-countries-group"
set member "block-country-brazil" "block-country-china" "block-country-lithuania" "block-country-netherlands" "block-country-russia" "block-country-sweden"
next
end
config firewall local-in-policy
edit 0
set intf "wan1"
set srcaddr "block-countries-group"
set dstaddr "all"
set service "ALL"
set schedule "always"
next
end
NSE4/FMG-VM64/FortiAnalyzer-VM/6.0 (FWF30E/FW92D/FGT200D/FGT101E/FGT81E)/ FAP220B/221C
There are multiple posts in this forum related to VIP policy compromising security. I have opened cases with FortiNet both for this issue and an additional issue. I have also alerted appropriate parties. To FortiNet's credit, they are working quickly to address this. I have not yet seen an official public statement from FortiNet. Please refer to the below correspondence to see if it pertains to your situation. Thank you.
(O.P.: not sure if it matters at this point, but I don't see a "set action deny" for rule 53 in the copy you took from the CLI.)
==========
Fw: FortiGate Security "Loophole" and Severe Bug
Two issues were discovered during FortiGate firewall product tests, the first a documentation issue which FortiNet has confirmed affects FortiOS 5.0.x and 5.2.x and the second a bug which affects any FortiGate "D" series in combination with FortiOS 5.0.10 (the FIPS 140 version; it is unknown whether other combinations of FortiOS and FortiGate are affected.)
1) FortiGate Deny All rules do not deny all traffic. What is documented: "VIP rules" take precedence over "regular rules." However, until two days ago (6/15/2015) after it was recently brought to their attention this was mentioned only briefly in a technical note and not in any of their standard documentation (the FortiOS handbook, admin guide, etc.) It remains inexplicit that "VIP rules" also take precedence over "Deny All" rules.
- Here's the link to the technical note (taken from the support case): http://kb.fortinet.com/kb/microsites/search.do?cmd=displayKC&docType=kc&externalId=FD33338
- Here's the link to the updated handbook, published 6/15/2015 (see page 956, "Exception to policy order (VIPs):") http://docs.fortinet.com/d/fortigate-fortios-handbook-the-complete-guide
The scenario documented in the stem support case is given below. Rules appear in the same order they would after issuing the commands "config firewall policy" and "get."
=====
config firewall policy
edit 1
set srcintf "wan1"
set srcaddr "outside_blacklist"
set dstintf "dmz"
set dstaddr "all"
set action deny
set schedule "always"
set service "ALL"
set logtraffic all
next
edit 2
set srcintf "wan1"
set srcaddr "all"
set dstintf "dmz"
set dstaddr "nat_inside"
set action accept
set schedule "always"
set service "ALL"
set logtraffic all
next
end
=====
In the above example, "outside_blacklist" is a group of outside addresses and "nat_inside" is a VIP on the firewall. As depicted, traffic will not follow the usual order of precedence. Any traffic destined for "nat_inside" will ignore the Deny All in Rule 1 but match the Accept in Rule 2. Below is the fix suggested by a FortiNet support engineer.
=====
config firewall policy
edit 1
set srcintf "wan1"
set srcaddr "outside_blacklist"
set dstintf "dmz"
set dstaddr "nat_inside"
set action deny
set schedule "always"
set service "ALL"
set logtraffic all
next
edit 2
set srcintf "wan1"
set srcaddr "all"
set dstintf "dmz"
set dstaddr "nat_inside"
set action accept
set schedule "always"
set service "ALL"
set logtraffic all
next
end
=====
Shown above, the change replaces the Deny All in Rule 1 with Deny "nat_inside." This in effect restores the order of precedence. (For an explanation, see the new section "Exception to policy order (VIPs)" in the handbook. For the alternative fix, "match-vip," see the technical note.) To summarize, FortiGate "VIP rules" are matched before "regular rules." Most significantly, "VIP rules" are matched before "Deny All" rules.
The potential for a security "loophole" as described in the above case is compounded by:
a) a reasonable (until two days ago) expectation that a Deny or Deny All policy always denies blacklisted traffic in order of precedence; and
b) typical industry practice that only denied traffic gets logged.
Given these factors, a configuration error which would allow blacklisted traffic to enter a network undetected via an Accept rule is not unlikely. [...]
2) The secondary unit in a FortiGate "D" series active/passive cluster bricks (i.e., fails closed and must be re-imaged) after the first couple FIPS self-tests under certain conditions, two of them being: when it can't contact the master; when it is given the master's configuration file. Anyone with "D" series units will not be able to maintain an active/passive cluster in FIPS-CC mode. An "emergency" code fix of FortiOS 5.0.10 is underway which will be released as 5.0.13. We have been assured by FortiNet this will not affect the FIPS 140 certification of FortiOS.
PCNSE
NSE
StrongSwan
A name can contain numbers (0-9), uppercase and lowercase letters (A-Z, a-z), spaces, and the special characters - and _
Improper naming can cause problems that are hard to diagnose.tells me to not even consider using different special characters, as results seem to be unpredictable.
PCNSE
NSE
StrongSwan
It is not so much about XSS but rather to rule out an unknown variable. While speculative to a certain degree, comments in this forum, i.e. here, indicate that things can get messed up quickly. Just imagine what happened if the labels/names get truncated at illegal characters, under certain conditions, when the text configuration is compiled into the running config...you never known unless you have written the configuration parser.
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1548 | |
1032 | |
749 | |
443 | |
210 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.