- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
power button continuously flashing green issue
Dear All ,
hope you are doing great,
i have FortiGate 60D, just unplugged it from the server room to hardware reset everything,
put on my desk, plugged the power and all i got the power button is contiguously flashing green,
it was working fine.
tried to putty it with no access.
your support much appreciated if anyone faced this before.
Regards
Ghadamsi
Solved! Go to Solution.
- Labels:
-
FortiGate
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Ghadamsi82 ,
Is the 'power' light or the 'status' light that is flashing green? Status light flashing green means that the FortiGate is booting up.
Have you tried to connect the FortiGate to console (see link below) and then reboot it? Do you see any message on the console output after the reboot (or disconnect/reconnect power)?
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-connect-to-the-FortiGate-console-po...
Best regards,
If you have found a useful article or a solution, please like and accept it to make it easily accessible to others.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi, it's almost certainly the power supply that's broken. Get a new one, I'm pretty sure it will start again. It happened every now and then with the D series Fortigates.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear FortiMax_it,
will look for new Power Supply to test,
thanks for your input.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Ghadamsi82 ,
Is the 'power' light or the 'status' light that is flashing green? Status light flashing green means that the FortiGate is booting up.
Have you tried to connect the FortiGate to console (see link below) and then reboot it? Do you see any message on the console output after the reboot (or disconnect/reconnect power)?
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-connect-to-the-FortiGate-console-po...
Best regards,
If you have found a useful article or a solution, please like and accept it to make it easily accessible to others.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thanks fricci_FTNT for the reply,
Only the 3 green small vertical next to Fatigate Logo and the Power Bottons are continuously nonstop flashing
attached the Putty screen shot of what i got.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Ghadamsi82 ,
Thank you for checking it. We should see at least some message appearing on the console, at this point the problem should be the power supply as suggested by FortiMax_it.
Best regards,
If you have found a useful article or a solution, please like and accept it to make it easily accessible to others.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear fricci_FTNT,
it was power supply, many thanks to your support.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi, it's almost certainly the power supply that's broken. Get a new one, I'm pretty sure it will start again. It happened every now and then with the D series Fortigates.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dear FortiMax_it,
will look for new Power Supply to test,
thanks for your input.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes, it was Power Supply issue,
Many thanks to your support.
