VLAN interface not accumulating traffic counters

[mackdav1]

I have an active-passive cluster of FG-201Fs running 7.2.5. On each member I have a Aggregate interface composed of two 10G X interfaces, with VLAN interfaces defined on the Aggregat

When I look at SNMP counters for one particular interface, it is not accumulating any counts for any of the parameters. I've manually pulled the SNMP values for this interface and they remain at zero.

If I create a Traffic graph for the interface on a Dashboard, the graph remains at zero over time.

Meanwhile an apparently identically defined VLAN interface on the same aggregate is showing traffic accumulations and generating traffic graphs in a credible way.

I am 99.999% sure traffic is passing across this VLAN, if I do a "di sniff packet any..." it will show packets traversing the VLAN, Aggregate, and physical X interfaces.

I've tried manually changing the snmp-id of the interface, but that hasn't worked.

Any idea what I've done wrong?

[pgautam]

 Hi,

Please share the below commands output to check traffic counters on the VLAN interface for the working and non-working VLAN

diagnose netlink interface list <name of the interface>

dia sniffer packet <lan_interface_name> 4 0 a

Regards 

Priyanka

- Have you found a solution? Then give your helper a "Kudos" and mark the solution.

[mackdav1]

fw-zz-z1-A (ZZ-Z1-PF-1) # di netlink interface list name ZZ-Z1-EINET-520

if=ZZ-Z1-EINET-520 family=00 type=1 index=52 mtu=9216 link=0 master=0
ref=61 state=start present fw_flags=18003800 flags=up broadcast run promsic multicast
Qdisc=noqueue hw_addr=00:09:0f:09:01:1a broadcast_addr=ff:ff:ff:ff:ff:ff
stat: rxp=191002604 txp=125518139 rxb=112878320337 txb=35035491349 rxe=0 txe=0 rxd=0 txd=0 mc=0 collision=0 @ time=1694118613
re: rxl=0 rxo=0 rxc=0 rxf=0 rxfi=0 rxm=0
te: txa=0 txc=0 txfi=0 txh=0 txw=0
misc rxc=0 txc=0
input_type=0 state=3 arp_entry=0 refcnt=61

fw-zz-z1-A (ZZ-Z1-PF-1) # di netlink interface list name ZZ-Z1-EINET-522

if=ZZ-Z1-EINET-522 family=00 type=1 index=72 mtu=9216 link=0 master=0
ref=402 state=start present fw_flags=18000000 flags=up broadcast run promsic multicast
Qdisc=noqueue hw_addr=00:09:0f:09:01:1a broadcast_addr=ff:ff:ff:ff:ff:ff
stat: rxp=0 txp=0 rxb=0 txb=0 rxe=0 txe=0 rxd=0 txd=0 mc=0 collision=0 @ time=1694118618
re: rxl=0 rxo=0 rxc=0 rxf=0 rxfi=0 rxm=0
te: txa=0 txc=0 txfi=0 txh=0 txw=0
misc rxc=0 txc=0
input_type=0 state=3 arp_entry=0 refcnt=402

Running an (adjusted) packet sniff command shows packets traversing both interfaces.

[mackdav1 · Accepted solution]

So it turns out that turning it off and on again solved the problem. Specifically in this case, rebooting the A member, waiting for it to return and then rebooting the B member enabled counters to work correctly.