- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Typing not working in the serial console of FortiSwitch 124F
I have a FortiSwitch 124F which is working fine apart from one worrying thing: if I connect to its serial console, I can see what it's typing, but when I am typing - no characters appear. For example, when I reboot the device with the serial cable connected, I can see the messages and eventually a login prompt. But I cannot log in as the switch is deaf to my typing.
The serial cable itself appears to be healthy - it works perfectly if I connect to a different device, for example to FortiGate 40F.
I tried switching the baud rate down to 9600 but that did not help. Now I am out of ideas.
Please somebody suggest what I could be done?
- Labels:
-
FortiSwitch
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Try physically check the switch's console port if the pins are all ok.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The console port pins look perfectly fine.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
First, are you using the console cable came within the shipping box? You might have some problem if you're using a different kind like Cisco console cable. The same console cable works perfectly fine with "E" model or "D" model of FortiSwitch.
I had to RMA an FS108F multiple times because when I type "a" it showed "A" or different characters. When I used the console cable from FTNT, it worked fine. Something hardware must be different on "F" Sereies FSWs.
Toshi
Created on 05-14-2024 03:32 PM Edited on 05-14-2024 03:32 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Of course those different console cables work fine with any type of FGTs, including 40F, 60F, 100F and so on. Only "F" Series FSW seems to be different based on my experience.
Toshi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I am 90% sure it is the one. The cable looks just like in the manual, and I fished it out of the box of the switch. There is a small possibility that someone could have thrown a wrong serial cable in and removed the correct one, but that's unlikely. Also, it definitely is not a Cisco one.
Could it be that the switch is configured to have a read-only serial console? If so, where might it be?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Fortinet cable is like the one shown below, I got one in a newly acquired FSW 124F.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @rtvd,
Please refer to the QuickStart Guide: https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/67241563-25de-11eb-96b9-005056...
1. Connect the Console Port with a Console Cable to the USB Port on the Management Computer.
2. Start a terminal program on the Management Computer and select an available COM Port using the following default settings:
Baud rate: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @hbac,
This is exactly what I tried and it did not work. I also tried switching the baud rate to 9600 both in the configuration and the terminal - same problem.
My cable is different to the one shown in @AEK, post. However, the QuickStart Guide for my FortiSwitch 124F is different too, and shows a different (older?) cable.
Given that I am taking the correct steps and it does not work, I guess I can try to purchase a totally new serial cable and try it with it. If that does not work either, it must be a fault in the switch, correct?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
yeah, that's what I would do to make sure it's not a cable issue. In my case I have at least 4-5 console cables from Cisco and FTNT, and others. My 108F came with a black DB-9 cable like yours.
Then open a ticket at TAC. It might be just defective hardware if it never worked before. RMA is needed if that's the case.
Toshi