- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
SUBNET
help me guys im new with fortinet my question is i have existing router MIKROTIK i have 16 subnet all connected in one interface but planning all to transfer in fortinet 200e the same configuration because some of my switch is not manage switch. how to config one interfaces with 16 subnet thanks
Nominate a Forum Post for Knowledge Article Creation
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
You do secondaries . I believe you can do up to 16 secondaries per interface
PCNSE
NSE
StrongSwan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The max value doc for 6.0 says up to even 32/interface.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
thanks for your reply but. what i need is i can configure in one interface the vlan. more that 16 subnet but my question is not working in ordinary switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
my existing connection in one interfaces only all the 16 subnet are connected in one interfaces. i want to make the same in FGT so how.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
You need to explain your cfg secondarys are easier and vlans are easy we are not sure what your doing
e.g secondary
config system interface edit "dmz" set vdom "root" set ip 10.10.10.1 255.255.255.0 set allowaccess ping https http fgfm capwap set type physical set role dmz set snmp-index 5 set secondary-IP enable config secondaryip edit 1 set ip 10.200.1.1 255.255.255.0 next edit 2 set ip 10.200.2.1 255.255.255.0 next edit 3 set ip 10.200.3.1 255.255.255.0 next edit 4 set ip 10.200.4.1 255.255.255.0 next edit 5 set ip 10.200.5.1 255.255.255.0 next edit 6 set ip 10.200.6.1 255.255.255.0 next edit 7 set ip 10.200.7.1 255.255.255.0 next edit 8 set ip 10.200.8.1 255.255.255.0 next edit 9 set ip 10.200.9.1 255.255.255.0 next edit 10 set ip 10.200.10.1 255.255.255.0 next edit 11 set ip 10.200.11.1 255.255.255.0 next edit 12 set ip 10.200.12.1 255.255.255.0 next edit 13 set ip 10.200.13.1 255.255.255.0 next edit 14 set ip 10.200.14.1 255.255.255.0 next edit 15 set ip 10.200.15.1 255.255.255.0 next edit 16 set ip 10.200.16.1 255.255.255.0 next edit 17 set ip 10.200.17.1 255.255.255.0 next end nextend Ken
PCNSE
NSE
StrongSwan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
sir why do i need DMZ.? only i need to config internal connection between the 17 different ip address. i want all this can connect each other.
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sir, Please check the image. i need all of my ip range connect in any port so how/?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
You can change the firewall from switch to interface mode:
https://kb.fortinet.com/kb/documentLink.do?externalID=FD40353
Then you can use secondary IPs (subnet) on the Interface as suggested previously or you can a create VLAN interface for each subnet.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
thanks for the reply here is my picture of my network that i want thanks