Hello,
we have the following constellation:
Location 1 -> Fortigate 200
Location 2 -> Fortigate 200
IPSEC VPN between for routing traffic from vlan 72 location 1 to vlan 73 location 2
This works well.
Now our colleagues want to use ssl vpn from home to get also access to vlan 72 in location one and vlan 73 in location two.
I configured ssl vpn on location 1 fortigate and it works for getting access to vlan 72. I also setup a policy to vlan 73 but didn't worked so far.
Any idea or is this technically not possible and I need to configure a second ssl vpn on location 2 firewall?
Thanks for you help :)
Solved! Go to Solution.
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Hi @Pkay983,
On location 2, packet arrived on VPN tunnel but it dropped on policy 0 which means there is no policy allow traffic. Can you please check there is policy allow 192.168.111.1 from "vpn-to-loc1" to 192.168.2.1 on local interface?
Regards,
Minh
Dear Pkay983,
Please share below output and initiate the traffic
diag sniff packet any 'host x.x.x.x and icmp' 4 0 l >> where x.x.x.x is the dst IP
Collect the flow debug too
https://docs.fortinet.com/document/fortigate/6.2.15/cookbook/54688/debugging-the-packet-flow
SSL VPN Pool: 192.168.111.0/24
Subnet Location 2: 192.168.2.0/24
Fortigate Location 1:
2023-09-26 09:12:47.011276 ssl.root in 192.168.111.1 -> 192.168.2.1: icmp: echo request
2023-09-26 09:12:47.011285 vpn-to-loc2 out 192.168.111.1 -> 192.168.2.1: icmp: echo request
Fortigate Location 2:
2023-09-26 09:13:07.019100 vpn-to-loc1 in 192.168.111.1 -> 192.168.2.1: icmp: echo request
2023-09-26 09:13:12.022161 vpn-to-loc1 in 192.168.111.1 -> 192.168.2.1: icmp: echo request
2023-09-26 09:13:17.027890 vpn-to-loc1 in 192.168.111.1 -> 192.168.2.1: icmp: echo request
Hi,
Yes, it is possible to configure SSL VPN to IPSec VPN. You may refer to this link for the same:
https://docs.fortinet.com/document/fortigate/7.4.1/administration-guide/45836/ssl-vpn-to-ipsec-vpn#:....
BR,
Manosh
I guess I did it right... the only difference is, that I use:
IPSEC Phase 2:
local Address Subnet 0.0.0.0 / 0.0.0.0
Remote Address Subnet 0.0.0.0 / 0.0.0.0
I also added a static route from the location 2 firewall to the ssl vpn pool... but didn't work.
from diag sniffer it looks like its going through the ipsec tunnel but not back
Hi @Pkay983,
Please run the debug flow on both FortiGates to see where the traffic is being dropped. https://docs.fortinet.com/document/fortigate/7.4.1/administration-guide/54688/debugging-the-packet-f...
Regards,
Thanks for your replies :)
Location 1:
FW_Loc1 # id=20085 trace_id=26 func=print_pkt_detail line=5844 msg="vd-root:0 received a packet(proto=1, 192.168.111.1:1->192.168.2.1:2048) tun_id=0.0.0.0 from ssl.root. type=8, code=0, id=1, seq=8000."
id=20085 trace_id=26 func=resolve_ip_tuple_fast line=5930 msg="Find an existing session, id-6689a1bc, original direction"
id=20085 trace_id=26 func=vf_ip_route_input_common line=2605 msg="find a route: flag=04000000 gw-XXXIPLOC2XXX via vpn-to-loc2"
id=20085 trace_id=26 func=ipsecdev_hard_start_xmit line=669 msg="enter IPSec interface vpn-to-loc2, tun_id=0.0.0.0"
id=20085 trace_id=26 func=_do_ipsecdev_hard_start_xmit line=229 msg="output to IPSec tunnel vpn-to-loc2"
id=20085 trace_id=26 func=esp_output4 line=844 msg="IPsec encrypt/auth"
id=20085 trace_id=26 func=ipsec_output_finish line=544 msg="send to xxx.xxx.xxx.xxx via intf-vlan-42"
id=20085 trace_id=27 func=print_pkt_detail line=5844 msg="vd-root:0 received a packet(proto=1, 192.168.111.1:1->192.168.2.1:2048) tun_id=0.0.0.0 from ssl.root. type=8, code=0, id=1, seq=8005."
Location 2
id=20085 trace_id=6 func=print_pkt_detail line=5844 msg="vd-root:0 received a packet(proto=1, 192.168.111.1:1->192.168.2.1:2048) tun_id=XXXIPLOC1XXX from vpn-to-loc1. type=8, code=0, id=1, seq=7988."
id=20085 trace_id=6 func=init_ip_session_common line=6023 msg="allocate a new session-021f4f6a, tun_id=141.73.50.132"
id=20085 trace_id=6 func=vf_ip_route_input_common line=2605 msg="find a route: flag=80000000 gw-192.168.2.1 via root"
id=20085 trace_id=6 func=fw_local_in_handler line=500 msg="iprope_in_check() check failed on policy 0, drop"
id=20085 trace_id=7 func=print_pkt_detail line=5844 msg="vd-root:0 received a packet(proto=1, 192.168.111.1:1->192.168.2.1:2048) tun_id=XXXIPLOC1XXX from vpn-to-loc1. type=8, code=0, id=1, seq=7989.
Hi @Pkay983,
On location 2, packet arrived on VPN tunnel but it dropped on policy 0 which means there is no policy allow traffic. Can you please check there is policy allow 192.168.111.1 from "vpn-to-loc1" to 192.168.2.1 on local interface?
Regards,
Minh
There was a policy, but I added it with the FortiManager... I deleted it and added it again direct on the forti and this did the trick.
Well thanks @All for the hints.
Well done :)
Hi @Pkay983.
Did you have the route to the new SSL VPN subnet on the remote site? Please also check on both side if there are bi-directional policy to allow this flow of traffic.
Regards,
Minh
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1698 | |
1092 | |
752 | |
446 | |
228 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.