Hi,
We using fortigte FG100E with fw v.6.0.2 build 0.6.1.3, we already configure failover with policy base routing. All working normal and monitor with link-monitor. The problem is when one link problem notification sent to email goes to junk mail. aftter i check the mail header there is no from mail .
From: <>
Message-Id: <1664016217.30@notification.fortinet.net>
Reply-To: noreply@notification.fortinet.net
How to add From email (example from my email) to this? so notification next goes to inbox.
appreciate for suggestion.
Thank you
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Hello Agus,
How is the notification email configured on Fortigate? Automation stitch or something else? Kindly share the notification email config.
Best Regards,
Mohammed Ahmed
Probably because you didn't configure "set reply-to" under "config system email-server" in CLI.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-configure-alert-email-settings/ta-p...
Toshi
Hi All,
Sorry for late reply and thank you for the contribution, here is configuration on our site
tick enabled
From: myemail
To: recipient email
Alert parameter: event
config system email-server
set reply-to "myemail@mydomain.com"
set server "notification.fortinet.net"
set port 465
set security smtps
end
Thank you
Maybe an issue with the old 6.0.2? The config looks fine.
My home 40F uses the same default "notification.fortinet.net" as SMTP server and no "reply-to" is configured. But it's 6.4.10 and the config has "set username" configured and the source email has this username in alert email. Does your 6.0.2 have "set username" command?
Toshi
Hi, Thank for your reply appreciate,
i check on my device there is no set username command
FG100 (email-server) # set
type Use FortiGuard Message service or custom email server.
reply-to Reply-To email address.
server SMTP server IP address or hostname.
port SMTP server port.
source-ip SMTP server IPv4 source IP.
source-ip6 SMTP server IPv6 source IP.
authenticate Enable/disable authentication.
validate-server Enable/disable validation of server certificate.
security Connection security used by the email server.
ssl-min-proto-version Minimum supported protocol version for SSL/TLS connections (default is to follow system global setting).
Thank you
Hi,
After i check detail on alert email for link-status monitor change
FG100E (automation-action) # edit "Link monitor change_email"
FG100E (Link monitor cha~ail) # show
config system automation-action
edit "Link monitor change_email"
set action-type email
set email-to "myemail@mydomain.com"
set email-subject "Link monitor change"
next
end
FG100E (Link monitor cha~ail) # set email-from myemail@mydomain.com
command parse error before 'email-from'
Command fail. Return code -61
FG100E (Link monitor cha~ail) #
set Modify value.
unset Set to default value.
select Select multi-option values.
unselect Unselect multi-option values.
append Append values to multi-option.
clear Clear multi-option values.
get Get dynamic and system information.
show Show configuration.
next Configure next table entry.
abort End and discard last config.
end End and save last config.
FG100E (Link monitor cha~ail) # set
action-type Action type.
email-to Email addresses.
email-subject Email subject.
minimum-interval Limit execution to no more than once in this interval (in seconds)
still confuse how to add mail from, so when receive alert have mail from address from myemail@mydomain.com not no sender receive that cause sent to junk folder.
Thank you
Hello Agus,
Kindly try using alert mail settings as per KB :https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-configure-alert-email-settings/ta-p...
config alertemail setting
set mailto1 myemail@mydomain.com
Best Regards,
Mohammed Ahmed
Hi, appreciate for your help, already try link above but its happen with link status monitor, i have 2 WAN failover, when i got 1 link problem it will send notification alert for link change, it's working but goes to junk folder because i check there is no "from".
Thank you
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1696 | |
1091 | |
752 | |
446 | |
228 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.