Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
Aaron_Abrincia_Meimb
New Contributor II

Memory Usage goes high

HI Engineers, Would you able to explain to me why we are reaching 73% of memory and could it possible to decrease the consumption of the memory? Regards Aaron
Network Engineer
Network Engineer
17 REPLIES 17
MikePruett
Valued Contributor

Do you have a policy near the top of your rule set that has IPS on it in which most traffic hits? It looks like your IPS sensors are eating it alive because of traffic levels and work load.
Mike Pruett Fortinet GURU | Fortinet Training Videos
ramakien89
New Contributor

Hi!

I am using Fortigate 100D with spec:

HA StatusStandalone [link=https://192.168.0.1/system/ha/monitor][Configure][/link]Host NameFG100D3G16829885 [link=https://192.168.0.1/ng/system/hostname][Change][/link]Serial NumberFG100D3G16829885Operation ModeNATInspection ModeProxy-based [link=https://192.168.0.1/p/system/vdom/edit/root/][Change][/link]System TimeMon May 8 18:50:57 2017 (FortiGuard) [link=https://192.168.0.1/ng/system/time][Change][/link]Firmware Versionv5.4.3,build1111 (GA) [link=https://192.168.0.1/ng/system/firmware/?viewOnly][Update][/link]System Configuration[link=https://192.168.0.1/ng/system/config/backup][Backup][/link]  [link=https://192.168.0.1/ng/system/config/restore/][Restore][/link]  [link=https://192.168.0.1/ng/system/config/revisions][Revisions][/link]Current Administratoradmin [link=https://192.168.0.1/system/status/status][Change Password][/link] /2 in Total [link=https://192.168.0.1/ng/system/admin/current][Details][/link]Uptime2 day(s) 1 hour(s) 42 min(s)Virtual DomainDisabled [link=https://192.168.0.1/system/status/status][Enable][/link]

In 2 day work, device will upto 80% memory usage, need reboot, if not reboot, memory will upto 85% then device will can not work, internet wrong, I did turn off and turn on device by button on device. 

 

terry_vos

Watching for resolution. I have a similar issue with High Memory and/or CPU causing Conserve Mode events. I do have  a ticket open with CS, but extra eyes on something never hurts.

Running an HA pair of 240D, firmware 5.4.4, build 1117.

terry_vos
New Contributor

Sorry - just realized that the original post is from 2014. Doubt that I will see resolution here.

 

Moderator - please feel free to REMOVE both of my posts on this thread.

mike_dp

240D only has 2gb I believe of RAM so that's not much. Make sure to have UTM policies on the bottom you may also consider upgrading to a bigger box.

 

Fortigate : 80E, 80F, 100E, 200F, 300E : 6.4.6

FortiAnalyzer, ForticlientEMS

Fortigate : 80E, 80F, 100E, 200F, 300E : 6.4.6 FortiAnalyzer, ForticlientEMS
ede_pfau

FG-240D has 4 GB of RAM. I'd say that is ample.

Something else is causing the high consumption - maybe an update process running wild after a signature update, or an engine update.

Reboot doesn't help?

Ede Kernel panic: Aiee, killing interrupt handler!
Ede Kernel panic: Aiee, killing interrupt handler!
mynghecaocap
New Contributor

Oh no, I'm getting same issue with Memory Usage , anybody can please explain this problem?

Gỗ mỹ nghệ cao cấp
MikePruett

the older FortiOS had some memory leak issues. Every device I have had that has experienced this has been resolved as we progressed through FortiOS versions

Mike Pruett Fortinet GURU | Fortinet Training Videos
Announcements

Select Forum Responses to become Knowledge Articles!

Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.

Labels
Top Kudoed Authors