im trying to set domain on phase1-interface but i get the error
command parse error before 'domain'
Command fail. Return code -61
From what ive found only mode cfg should have to be enabled and type dynamic?
Am i missing anything
this is the config:
edit "<Withdrawn>"
set type dynamic
set interface "wan"
set ip-version 4
set ike-version 2
set local-gw 0.0.0.0
set keylife 86400
set authmethod psk
unset authmethod-remote
set peertype any
set net-device disable
set exchange-interface-ip disable
set aggregate-member disable
set mode-cfg enable
set ipv4-dns-server1 <Withdrawn>
set ipv4-dns-server2 <Withdrawn>
set ipv4-dns-server3 0.0.0.0
set ipv4-wins-server1 0.0.0.0
set ipv4-wins-server2 0.0.0.0
set ipv6-dns-server1 ::
set ipv6-dns-server2 ::
set ipv6-dns-server3 ::
set proposal aes192-sha256 aes256-sha256
set add-route enable
set localid ''
set localid-type auto
set negotiate-timeout 30
set fragmentation enable
set ip-fragmentation post-encapsulation
set dpd on-idle
set forticlient-enforcement disable
set comments ''
set npu-offload enable
set dhgrp 14
set suite-b disable
set eap enable
set eap-identity send-request
set acct-verify disable
set ppk disable
set wizard-type custom
set reauth disable
set authusrgrp "<Withdrawn>"
set idle-timeout disable
set ha-sync-esp-seqno enable
set fgsp-sync disable
set inbound-dscp-copy disable
set auto-discovery-sender disable
set auto-discovery-receiver disable
set auto-discovery-forwarder disable
set nattraversal enable
set fragmentation-mtu 1200
set childless-ike disable
set rekey enable
set enforce-unique-id disable
set fec-egress disable
set fec-ingress disable
set network-overlay disable
set default-gw 0.0.0.0
set default-gw-priority 0
set assign-ip enable
set assign-ip-from name
set ipv4-netmask 255.255.255.255
set dns-mode manual
set ipv4-split-include "<Withdrawn>"
set split-include-service ''
set ipv4-name "<Withdrawn>"
set ipv6-prefix 128
set ipv6-split-include ''
set ipv6-name ''
set ip-delay-interval 0
set save-password enable
set client-auto-negotiate enable
set client-keep-alive disable
set psksecret ENC <Withdrawn>
set keepalive 10
set distance 15
set priority 1
set dpd-retrycount 3
set dpd-retryinterval 60
next
end
Solved! Go to Solution.
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Please note that 'set domain' only available in IKEv1.
Regards,
Hi @pelskyl,
Yes, the 'set domain' command should work. Which firmware version are you using?
Regards,
That fw is on 7.0.12
I tested in my lab. It should work with both wizard-types. However, you need to enable unity-support first (it is enabled by default).
config vpn ipsec phase1-interface
edit <>
set unity-support enable
set domain example.com
end
Regards,
Thats why its not working then since its an ikev2!
Then i need to figure out another way to push it
Hi, you may refer here and see if it's working for you: https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-set-DNS-suffix-for-VPN-SSL-and-IPse...
Thanks but i already have all thoose settings on phase1, thats the wierd part.
You're welcome. I did a quick test for version 7.0.12 and I'm able to set the domain. Here's my config for your reference:
edit "test"
set type dynamic
set interface "port1"
set ip-version 4
set ike-version 1
set local-gw 0.0.0.0
set keylife 86400
set authmethod psk
set mode main
set peertype any
set net-device disable
set exchange-interface-ip disable
set aggregate-member disable
set mode-cfg enable
set ipv4-dns-server1 0.0.0.0
set ipv4-dns-server2 0.0.0.0
set ipv4-dns-server3 0.0.0.0
set ipv4-wins-server1 0.0.0.0
set ipv4-wins-server2 0.0.0.0
set ipv6-dns-server1 ::
set ipv6-dns-server2 ::
set ipv6-dns-server3 ::
set proposal aes128-sha256 aes256-sha256 aes128-sha1 aes256-sha1
set add-route enable
set localid ''
set localid-type auto
set negotiate-timeout 30
set fragmentation enable
set ip-fragmentation post-encapsulation
set dpd on-idle
set forticlient-enforcement disable
set comments "VPN: test (Created by VPN wizard)"
set npu-offload enable
set dhgrp 14 5
set suite-b disable
set wizard-type static-fortigate
set xauthtype disable
set idle-timeout disable
set ha-sync-esp-seqno enable
set fgsp-sync disable
set inbound-dscp-copy disable
set auto-discovery-sender disable
set auto-discovery-receiver disable
set auto-discovery-forwarder disable
set nattraversal enable
set esn disable
set rekey enable
set enforce-unique-id disable
set fec-egress disable
set fec-ingress disable
set default-gw 0.0.0.0
set default-gw-priority 0
set assign-ip enable
set assign-ip-from range
set ipv4-start-ip 0.0.0.0
set ipv4-end-ip 0.0.0.0
set ipv4-netmask 255.255.255.255
set dns-mode manual
set ipv4-split-include ''
set split-include-service ''
set ipv6-start-ip ::
set ipv6-end-ip ::
set ipv6-prefix 128
set ipv6-split-include ''
set ip-delay-interval 0
set unity-support enable
set domain "test.com"
set banner ''
set include-local-lan disable
set ipv4-split-exclude ''
set ipv6-split-exclude ''
set client-auto-negotiate disable
set client-keep-alive disable
set keepalive 10
set distance 15
set priority 1
set dpd-retrycount 3
set dpd-retryinterval 60
next
end
Yea it is possible, since we have it on old tunnel, can it be set wizard-type custom that prevents me from using that setting?
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1688 | |
1087 | |
752 | |
446 | |
227 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.