Good Morning!
I've got a 60C unit that stopped responding. On a HQIP test it accused disk problems. Can i still use this unit as a temporary replacement? Follows HQIP LOG:
FortiGate-60C (16:24-09.28.2011) Ver:04000026 Serial number: FGT60C3G11021972 CPU(00): 525MHz Total RAM: 512MB Initializing boot device... Initializing MAC... nplite#0 Press any key to display configuration menu... ...... Reading boot image... 1538645 bytes. Initializing firewall...
System is started.
Test program loading(HQIP, Build1003,Dec 15 2010 19:42:45) ...
You are running HQIP test program. To start testing, login as "admin" without password, and type: diagnose hqip start
HQIP login: admin Password: Welcome !
HQIP # diagnose hqip start
HQIP mode is: base expcard memory hdd std_nic usb
Fortinet Hardware Quick Inspection
Instructions:
- Wire the network ports as following for NIC loopback test. [PORT1 - PORT2] [PORT3 - PORT4] [PORT5 - WAN1] [WAN2/Express Card - DMZ]
Press any key to continue ... Test Begin at UTC Time Thu Mar 12 03:21:59 2015
==> BIOS Integrity Check
Gathering system information...... Model Name:[FGT60C] Unit BIOS Version:[04000026] Unit Fortinet SN:[FGT60C3G11021972] Unit OEM SN:[FGT60C3G11021972] Unit First MAC:[00090F1C2792]
Checking BIOS checksum...Good
License is good!
<== BIOS Integrity Check - PASS
==> System Configuration Check
Processor: FA526id(wb) rev 1 (v4l) CPU number: 1 CPU MIPS: 524 Total Memory: 450676 KB Boot Device: sda Size: 7640 MB
dmz macaddress: 00:09:0F:1C:27:95 internal1 macaddress: 00:09:0F:1C:27:92 internal2 macaddress: 00:09:0F:1C:27:99 internal3 macaddress: 00:09:0F:1C:27:98 internal4 macaddress: 00:09:0F:1C:27:97 internal5 macaddress: 00:09:0F:1C:27:96 wan1 macaddress: 00:09:0F:1C:27:93 wan2 macaddress: 00:09:0F:1C:27:94
Total 8 net port(s) found.
<== System Configuration Check - PASS
==> Memory Test
pagesize=4096, pagesizemask=FFFFF000 Detecting memory(440MB)...[Done, 223MB will be tested]
STRESS->MEM-> 1.Stuck Address... STRESS->MEM-> 1.Stuck Address PASSED. STRESS->MEM-> 2.Random value... STRESS->MEM-> 2.Random value PASSED. STRESS->MEM-> 3.XOR comparison... STRESS->MEM-> 3.XOR comparison PASSED. STRESS->MEM-> 4.SUB comparison... STRESS->MEM-> 4.SUB comparison PASSED. STRESS->MEM-> 5.MUL comparison... STRESS->MEM-> 5.MUL comparison PASSED. STRESS->MEM-> 6.DIV comparison... STRESS->MEM-> 6.DIV comparison PASSED. STRESS->MEM-> 7.OR comparison... STRESS->MEM-> 7.OR comparison PASSED. STRESS->MEM-> 8.AND comparison... STRESS->MEM-> 8.AND comparison PASSED. STRESS->MEM-> 9.Sequential Increment... STRESS->MEM-> 9.Sequential Increment PASSED. STRESS->MEM-> Round 0 completed in 164 seconds (0 errors).
Release memory done.
<== Memory Test - PASS
==> CPU Test
CPU check is done!
<== CPU Test - PASS
==> CPU/Memory Performance Test
48000000 bytes memory will be covered. vvvvvvvvvv Function Rate (MB/s) RMS time Min time Max time Copy: 154.8708 0.2075 0.2066 0.2086 Scale: 43.4650 0.7383 0.7362 0.7400 Add: 61.0996 0.7878 0.7856 0.7910 Triad: 35.6134 1.3573 1.3478 1.3602
<== CPU/Memory Performance Test - PASS
==> FortiASIC Test
Test FortiASIC SoC VPN.
ASIC SoC SSL testing... SSL ARC4 tested
SSL DES tested
SSL 3DES tested
SSL HMAC-MD5 tested
SSL HMAC-SHA1 tested
SSL AES 128bit tested
SSL AES 192bit tested
SSL AES 256bit tested
ASIC SoC SSL test PASSED.
<== FortiASIC Test - PASS
==> USB Test
There is no attached USB devices found.
<== USB Test - N/A
==> Boot Device Test
Testing write and read to hard disk(/dev/sda): Size 7640MB Timing buffered disk reads: read() hit EOF - device too small Timing buffered disk reads: hdtest.c(34): read() failed: Input/output error Timing buffered disk reads: hdtest.c(34): read() failed: Input/output error
HQIP login:
On a fresh firmware upload it also accuses problems on fgtag.c - 154: Disk Read Failed: Input/output error
Can i rely on this unit even with those Disk Errors?
Thanks!
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
I would suggest checking on the support site for a newer HQIP image and try loading/running that. If this was our own fgt I would reformat the bootdisk and load/install new firmware via tftp.
NSE4/FMG-VM64/FortiAnalyzer-VM/6.0 (FWF30E/FW92D/FGT200D/FGT101E/FGT81E)/ FAP220B/221C
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1688 | |
1087 | |
752 | |
446 | |
227 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.