Fortinet CPU and Memory

[Maik]

This post is not maintained anymore. Post your updates to this thread and rwpatterson will update his list: https://forum.fortinet.com/FindPost/100451 Building a Hardware CPU/Memory list. Disclaimer: This is a user contributed list. No liability assumed for accuracy and completeness. Fortigate: Model | Memory | CPU (Family, Mode) FGT 20C | ????? FGT 40C | 512MB ?Mhz | 1 FA526id(wb) rev 1 (v4l) FortiSOC FGT 50B | 256MB ?Mhz | 1 Geode Integrated Processor by AMD PCS @431Mhz (5,10) FGT 60 | 128 MB| CentaurHauls VIA Samuel 2 400Mhz FWF 60A | 128MB ?MHz | 1 CPU - CentaurHauls VIA Samuel 2 @ 400MHz (6,7) FWF 60B | 256MB ?MHz | 1 CPU - VIA Samuel 2 @ 400MHz (6,7) FGT 60C | 440 MB | FortiSOC (FA526id(wb) rev 1 (v4l), BogoMIPS: 524.28) FWF 60C | 440 MB | FortiSOC (FA526id(wb) rev 1 (v4l), BogoMIPS: 524.28) FGT 80C | 512MB ?Mhz | 1 CPU - Celeron (Covington) @ 600MHz (6,5) FGT 80C Rev2| 1024MB ?Mhz | ? CPU | 8GB Flash for logging etc. FWF 80CM | 512MB ?Mhz | 1 CPU - Celeron (Covington) @ 600MHz (6,5) FGT82C | 512MB ?Mhz | 1 CPU - Genuine Intel processor @ 600MHz | (the difference of 80C are the internal storage of 1TB) FGT 100A | 256MB ?Mhz | Intel(R) Celeron(TM) CPU 400MHz FGT 110C | 1024MB 400MHz | 1 CPU - Intel(R) Celeron(R) M processor 600MHz FGT 100D | 2048 MB 1.8GHz | 1 CPU Intel Atom D525@1.80GHz (6,12) FGT 200A | 512MB ?Mhz | 1 CPU - Intel Celeron @ 400MHz FGT 200B | 1024MB ?MHz | 1 CPU - Celeron Covington@ 1.2GHz (6,5) FGT 300A | 512MB ?Mhz | 1 Intel Celeron CPU @2.00GHz (15,2) FGT 310B | 1024MB 667MHz | 1 CPU - Celeron 440 @ 2.0GHz (6,6) FGT 311B | 1024MB 667MHz | 1 CPU - Celeron 440 @ 2.0GHz (6,6) | (the difference of 310B are the internal storage and redundant power) FGT 300C |??????? FGT 400A | 512MB ?Mhz | 1 CPU - Intel Pentium 4 @ 2.80GHz FGT 600C |???????? FGT 620B | 2048MB ?Mhz | 2x Intel Core 2 Due E4300 @ 1.80Ghz FGT 800 | 1024MB ?Mhz | Mobile Genuine Intel(R) processor 1600MHz (6,9) FGT 800C | 8192MB | 4 - Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz FGT1000A | 1024MB 400Mhz | 2 CPU - Intel Xeon 3.2GHz (15,4) FGT1000AFA2| 1024MB 400Mhz | 2 CPU - Intel Xeon @ 3.2GHz | (the difference of 1000A are FA2 network processor and fiber interface) FGT1000C | 8192MB | 4 - Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz FGT1240B | 3096MB ?Mhz | 4 CPU - Intel(R) Xeon(R) CPU E5504 @ 2.00GHz FGT3040B | 12288MB | 8 CPU - Intel(R) Xeon(R) CPU E5540 @ 2.53GHz FGT3140B | 12288MB 800MHz | 4 CPU - Intel Xeon CPU E5540 @ 2.00GHz (6,10) FGT3240C |?????? FGT3600 | 2048MB ?MHz | 4 CPU - Intel Xeon @ CPU 2.40GHz FGT3810A | 3532MB ?Mhz | 4 CPU - AuthenticAMD 1.8Ghz FGT3950B | 12288MB ?Mhz | ? CPU FGT3950BRev2 | 24576MB | 12 CPU - Intel (R) Xeon (R) CPU X5690 @ 3.47GHz (two 6-core CPU' s) FGT 5001 | 2048MB ?MHz | 4 CPU - Intel(R) Xeon(TM) CPU 2.00GHz FGT 5005 | 3538MB ?MHz | 4 CPU - AuthenticAMD 1.8Ghz More to follow, contributors welcome CPU# diagnose hardware sysinfo cpu Mem#diagnose hardware sysinfo memory Detailed information (Memory Speed) is available from the serial port boot menu: 2x I [ I ]: Configuration and information. [ I ]: Display hardware information. e.g. cpu family : 6 model : 6 model name : Intel(R) Celeron(R) CPU 440 @ 2.00GHz memory : SDRAM 1024MB 667MHz Thanks to all supporter

[romanr · Accepted solution]

Fortigate 300D:

CPU: Intel(R) Core(TM) i3-3220 CPU @ 3.30GHz RAM: 8GB CP8

NP6

Storage:

Disk Internal-0(boot    ref:   14.9GB    type: SSD [ATA SanDisk SSD i110] dev: /dev/sda

Disk HDD             ref:  16 111.8GB    type: SSD [ATA F2CSTK251M3T-012] dev: /dev/sdb

[bartman10]

94D-POE

Warning.. Trying to upgrade to 5.2.1 causes a boot loop that can only be fixed with console cable and BIOS restore. Support said it's "a known issue"... ya.. thanks bro.. how about pulling the firmware or giving me a WARNING when I download it!?!

Oh.. they also changed the network device order.. so now if you have a site to site VPN between this unit and another FG.. you can't ping the 94D's lan interface from the remote FG cli. They also said this is how they all work.. Bzzt wrong.. I 5 of my other units don'd do this.. Support thinks all FG's do this because they use 60D's as test units. 300C, 90D,200D,40C all can ping the lan interface across a VPN tunnel from cli.. After support did more "looking" they now say this is because the VPN tunnels don't have IP addresses by default. When the FG goes to send the ping if the interface does not have an IP address it goes from top to bottom in order. So.. the Site to Site VPN does not have an IP address on the virtual adapter.. that's how the wizard makes it.. that's how it's done in the manual.. but now they just figured out it should or your internal PING from the CLI will go out over the WAN interface... figure that one out.. my god... 

Processor: ARMid(wb) rev 1 (v4l) model name: FortiSOC2 BogoMIPS: 897.84 Features: swp half thumb

Hardware: FSoC2_ASIC Revision: 0000 Serial: 0000000000000000 Imp: 0x66 Arch: 0x5 Part: 0x726 Ver: 0x1 Ctype: 14 DSize: 6 DASS: 8 DLEN: 32 ISize: 6 IASS: 8 ILEN: 32 Seperated TLB: Associativity 0 0x0005317f HUM: En Vec Base:0xffff0000 IC:En BP:Dis RomP:Dis SysP:En WB:En DC: En Align:En 0x00000000 SB: Dis DB:Dis RS:Dis

Model name: FortiGate-94D-POE ASIC version: CP0 ASIC SRAM: 64M CPU: FortiSOC2 Number of CPUs: 1 RAM: 1838 MB Compact Flash: 1917 MB /dev/sdb Hard disk: 30533 MB /dev/sda USB Flash: not available

Disk SSD 29.8GB type: SSD [ATA Mini PCIeDOM 1ME] partition ref: 1 29.8GB, 22.3GB free mounted: Y label: 322ED082506A01F8 dev: /dev/sda1

Disk USB-2 1.9GB type: USB [FORTINET 67_V060324_002] partition ref: 0 256.0MB, 213.0MB free mounted: N label: dev: /dev/sdb1

get hardware memory total: used: free: shared: buffers: cached: shm: Mem: 1927774208 1026007040 901767168 0 151937024 490545152 197787648 Swap: 0 0 0 MemTotal: 1882592 kB MemFree: 880632 kB MemShared: 0 kB Buffers: 148376 kB Cached: 479048 kB SwapCached: 0 kB Active: 230896 kB Inactive: 396696 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 1882592 kB LowFree: 880632 kB SwapTotal: 0 kB SwapFree: 0 kB

[Adrian_Lewis]

Anyone got any info on the 4th gen 100D yet? Wondering if it's had any improvements or if it's just a different vendor for some parts.

[mhe]

here the details of the 4th generation 100D:

#

Model name: FortiGate-100D
ASIC version: CP8
ASIC SRAM: 64M
CPU: Intel(R) Atom(TM) CPU D525   @ 1.80GHz
Number of CPUs: 4
RAM: 3955 MB
Compact Flash: 15331 MB /dev/sdb
Hard disk: 30533 MB /dev/sda
USB Flash: not available
Network Card chipset: Intel(R) PRO/1000 Network Connection (rev.0000)
Network Card chipset: bcm-sw Ethernet driver 1.0 (rev.)

cheers,

martin

[Carl_Wallmark]

mhe wrote:

here the details of the 4th generation 100D:

#

Model name: FortiGate-100D
ASIC version: CP8
ASIC SRAM: 64M
CPU: Intel(R) Atom(TM) CPU D525   @ 1.80GHz
Number of CPUs: 4
RAM: 3955 MB
Compact Flash: 15331 MB /dev/sdb
Hard disk: 30533 MB /dev/sda
USB Flash: not available
Network Card chipset: Intel(R) PRO/1000 Network Connection (rev.0000)
Network Card chipset: bcm-sw Ethernet driver 1.0 (rev.)

cheers,

martin

hmmmm, what did they change ?

[mhe]

don't know - but its a serial number affected by the "4th generation boot isssue" as described in the advisory.

[wega]

FGT 20C | 439MB | 1 FA526id(wb) rev 1 (v41)

Regards

WEGA

[FGTuser]

Gen2:

Compact Flash: 15331 MB /dev/sda Hard disk: 15272 MB /dev/sda

Gen3: 

Compact Flash: 1917 MB /dev/sdb Hard disk: 30533 MB /dev/sda

Gen4: 

Compact Flash: 15331 MB /dev/sda

Hard disk: 30533 MB /dev/sda

Who knows, what else. But CPU/MEM is the same.

[romanr · Accepted solution]

Fortigate 300D:

CPU: Intel(R) Core(TM) i3-3220 CPU @ 3.30GHz RAM: 8GB CP8

NP6

Storage:

Disk Internal-0(boot    ref:   14.9GB    type: SSD [ATA SanDisk SSD i110] dev: /dev/sda

Disk HDD             ref:  16 111.8GB    type: SSD [ATA F2CSTK251M3T-012] dev: /dev/sdb

[seadave]

Thinking of purchasing so thanks for posting.  Would be good to get this and 500D on the list.

[romanr]

dfollis wrote:

Thinking of purchasing so thanks for posting.  Would be good to get this and 500D on the list.

Can't access one - But the 500D has got an i5 Quad Core with ~2.6 GHz as far as I remember...