- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
FortiGate 200E Unable to Access Web GUI
Hello,
We have a FortiGate 200E as one of our devices.
After a factory reset by using the hole pin method, we are unable to access the device anymore.
The status flashed for a while, the ports flashed, then the port lights were stable, then status was normal again. Leading us to believe the factory reset was successful.
The computer IP is set to 192.168.1.1, netmask 255.255.255.0, gateway 192.168.1.99
Everything as instructed in the manual and online.
Connected to the management port as the sticker on the device says (connect to MGMT port and access the web UI on 192.168.1.99)
However, we are unable to access the device on the web and we cannot ping it.
We have experience with multiple other FortiGates and went through similar processes in the past year without issues.
What should we try?
Thank you.
Solved! Go to Solution.
- Labels:
-
FortiGate
Nominate a Forum Post for Knowledge Article Creation
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Vladimir_VM
Fortigate 200E do not have the External RESET button.
As per datasheet, there back and front panel do not have the word RES/RESET on it which means that it is not supported.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-To-Reset-To-Factory-Default-Configurat...
https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiGate_200E_Series.pdf
To factory reset your device please follow below guide instead.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-Formatting-and-loading-FortiGate-firmware-...
Arnold Dimailig
TAC Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please take the console access of Fortigate, any console cable will work.
Check the IP address on the mgmt interface and allow access,
# config system interface
# edit mgmt
# show
Make sure the IP and subnet are correct and "allowaccess" to HTTP, HTTPS, ping, and SSH.
Test the connectivity with ping, and make sure the pings are working.
If the pings are good that means the connectivity is perfect!
Later check the https port that has been used, (the default is 443).
# config system global
# set admin-sport
Another thing that needs to be taken care of is the certificate,
Please make sure either Fortinet_Factory or self-signed cert should be applied below.
config sys global
set admin-server-cert
end
Additionally, please check this kb article for further troubleshooting, https://community.fortinet.com/t5/FortiGate/Troubleshooting-Tip-Cannot-access-the-FortiGate-web-admi...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
Kindly connect the Fortigate with the console cable using putty application as per the below document and check whether it is showing any error.
Regards
Jamal
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
You may consider to connect to the unit over the console and follow the steps below:
Check routing table:
get router info routing-table all
Sniff the traffic:
diagnose sniffer packet any 'host <filter IP address>' 4 0 a
Collect debug flow:
diagnose debug flow filter daddr <filter IP address>
diagnose debug flow show function-name enable
diagnose debug flow trace start 100
diagnose debug enable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Vladimir_VM
Fortigate 200E do not have the External RESET button.
As per datasheet, there back and front panel do not have the word RES/RESET on it which means that it is not supported.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-To-Reset-To-Factory-Default-Configurat...
https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiGate_200E_Series.pdf
To factory reset your device please follow below guide instead.
https://community.fortinet.com/t5/FortiGate/Technical-Tip-Formatting-and-loading-FortiGate-firmware-...
Arnold Dimailig
TAC Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you, @adimailig
You are correct, it did not factory reset the device.
I am having difficulty accessing it through the console.
Need to purchase a new USB console cable.
Would any work or does it have to be FortiNet specific?
Once I get it I can proceed with the formal factory reset procedure
Regards, VM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
I am not aware about any Fortinet specific console requirements. Any cable should work.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Vladimir_VM any console cable should work.
**If you come across a resolution, kindly show your appreciation by liking and accepting it, ensuring its accessibility for others**
Arnold Dimailig
TAC Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Thank you @adimailig,
I was able to factory reset the device through the console.
I am now able to use the device properly from the web GUI.
Regards, VM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi @Vladimir_VM,
Are you able to ping 192.168.1.99? I also believe that 200E does not have any reset button. Maybe try to access using console or SSH instead of HTTPS.
Regards,
Minh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Please take the console access of Fortigate, any console cable will work.
Check the IP address on the mgmt interface and allow access,
# config system interface
# edit mgmt
# show
Make sure the IP and subnet are correct and "allowaccess" to HTTP, HTTPS, ping, and SSH.
Test the connectivity with ping, and make sure the pings are working.
If the pings are good that means the connectivity is perfect!
Later check the https port that has been used, (the default is 443).
# config system global
# set admin-sport
Another thing that needs to be taken care of is the certificate,
Please make sure either Fortinet_Factory or self-signed cert should be applied below.
config sys global
set admin-server-cert
end
Additionally, please check this kb article for further troubleshooting, https://community.fortinet.com/t5/FortiGate/Troubleshooting-Tip-Cannot-access-the-FortiGate-web-admi...