Support Forum
The Forums are a place to find answers on a range of Fortinet products from peers and product experts.
DenJSnz
New Contributor

Exclude dynamic WAN IP from RIP advertisement

Hi there,

I have two FTGs where I wanted to exclude a WAN IP when redistribute connected networks, FGT1 works just fine, FGT2 doesn't:

 

FGT1:

 

 

config router rip
config network
edit 1
set prefix 192.168.100.0 255.255.255.0
next
end
config redistribute "connected"
set status enable
set metric 10
set routemap "RIP"
end
config interface
edit "wan2"
set receive-version 2
set send-version 2
next
end
end
config router route-map
edit "RIP"
config rule
edit 1
set action deny
set match-interface "wan1"
next
edit 2
next
end
next
end

edit "wan1"
        set vdom "root"
        set mode dhcp
        set allowaccess ping fgfm
        set type physical
        set alias "StarLink"
        set lldp-reception enable
        set monitor-bandwidth enable
        set role wan
        set snmp-index 1
next

 

 

Whatever I get on wan1 interface is being excluded from RIP.

 

FGT2:

 

 

config router rip
    set default-metric 15
    config network
        edit 1
            set prefix 192.168.9.0 255.255.255.0
        next
    end
    config redistribute "connected"
        set status enable
        set metric 1
        set routemap "RIP"
    end
    config redistribute "static"
        set metric 3
    end
    config interface
        edit "LAN"
            set receive-version 2
            set send-version 2
        next
    end
end
config router route-map
    edit "RIP"
        config rule
            edit 1
                set action deny
                set match-interface "UFB"
            next
            edit 2
            next
        end
    next
end

 

 

 

    edit "wan1"
        set vdom "root"
        set allowaccess ping
        set type physical
        set alias "MyUFB"
        set device-identification enable
        set snmp-index 1
    next

edit "UFB"
        set vdom "root"
        set mode pppoe
        set allowaccess ping
        set role wan
        set snmp-index 10
        set username "user"
        set password ENC password
        set interface "wan1"
        set vlanid 10
    next

 

 

So, I tried to include wan1 as a match-interface together with "UFB" interface but still no luck. As of today my only way is to manually add IP addresses to the route-map list but this will stop working next time it renews the pppoe DHCP lease.

Any suggestions would be much appreciated.

Thanks.

5 REPLIES 5
Jean-Philippe_P
Moderator
Moderator

Hello DenJSnz, 

 

Thank you for using the Community Forum. I will seek to get you an answer or help. We will reply to this thread with an update as soon as possible. 

 

Thanks,

Jean-Philippe - Fortinet Community Team
Jean-Philippe_P
Moderator
Moderator

Hello DenJSnz,

 

We are still looking an answer for your question.

 

We will come back to you ASAP.

 

Thanks,

Jean-Philippe - Fortinet Community Team
akristof
Staff
Staff

Hello,

With match interface, as you concluded, it will block any route via that interface.

I can suggest to use prefix-list inside of route-map. As you have DHCP, I am assuming that it should be still IP from some network range. And you can put this network range in prefix list. Or other way around is just manually list subnets that you want to allow and block everything else.

Adrian
DenJSnz

Hi, thanks for the suggestion. I'm not sure if we're on the same page though, I don't think the match-interface is blocking any route... what it does for me it excludes the IP address on the matched interface from the RIP advertisement and that's exactly how I would like this to be. It does work that way on the FGT1 where I have an IP address directly on the wan interface. But it doesn't work on the FGT2 where the IP address is actually on the sub-interface (vlan10) of the wan interface. Thanks.

akristof

Hello,

That depends if you have multiple routes via that interface. To be honest, RIP I did not test for the very long time. If the match-interface VLAN does not work, feel free to open TAC ticket, to verify if is not a bug.

Adrian
Announcements

Select Forum Responses to become Knowledge Articles!

Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.

Labels
Top Kudoed Authors