Solved! Go to Solution.
Nominating a forum post submits a request to create a new Knowledge Article based on the forum post topic. Please ensure your nomination includes a solution within the reply.
Sorry to bump this thread, but been running into some issues.
Is it just me, or are the backups you get from SCP not the full backup of the device? I've only just noticed this now that I'm doing some analytics on the files themselves, but they aren't even close to full. On one device, a full backup from the GUI gets me a file with 40,000 lines. A scp backup using sys_config is just shy of 2,200. It doesn't have any vdoms. It's almost useless.
Is there a different command other than sys_config (or fgt-config) to get a proper, full backup?
nbctcp wrote:Ethon,
Can you please show me the steps
nbctcp,
I've attached the script for you. You can change according to your needs.
PS.: Script only for Windows OS.
Elthon Abreu FCNSA v5
Holy,
I've used the Putty Key Generation (Looking in "ProgramFiles\PuTTY" If you have putty installed). There is a variable "Key" on the script file. To create the user "bkp" you can use the config below:
config system admin edit "bkpusr" set trusthost1 "backup IP address only - for best security" set vdom "root" set ssh-public-key1 "ssh-rsa AAAAB3NzaC1yc2EAAAABJQAAAQEAhIasKun...." set password ****** next end
Best regards
Elthon Abreu FCNSA v5
Hello,
how to set a Password for a Backup user in this script?
thank you
elthon.abreu wrote:nbctcp wrote:Ethon,
Can you please show me the steps
nbctcp,
I've attached the script for you. You can change according to your needs.
PS.: Script only for Windows OS.
NSE 8
NSE 1 - 7
Holy wrote:Hello,
how to set a Password for a Backup user in this script?
thank you
elthon.abreu wrote:nbctcp wrote:Ethon,
Can you please show me the steps
nbctcp,
I've attached the script for you. You can change according to your needs.
PS.: Script only for Windows OS.
Holy,
I've used a *.pub key file for best security.
Elthon Abreu FCNSA v5
Hello,
thank you for the quick Answer.
and how can i do such *.pub key? and how do i set it Up for the Backup User to Authenticate?
Thank you in advance
elthon.abreu wrote:Holy wrote:Hello,
how to set a Password for a Backup user in this script?
thank you
elthon.abreu wrote:nbctcp wrote:Ethon,
Can you please show me the steps
nbctcp,
I've attached the script for you. You can change according to your needs.
PS.: Script only for Windows OS.
Holy,
I've used a *.pub key file for best security.
NSE 8
NSE 1 - 7
Holy,
I've used the Putty Key Generation (Looking in "ProgramFiles\PuTTY" If you have putty installed). There is a variable "Key" on the script file. To create the user "bkp" you can use the config below:
config system admin edit "bkpusr" set trusthost1 "backup IP address only - for best security" set vdom "root" set ssh-public-key1 "ssh-rsa AAAAB3NzaC1yc2EAAAABJQAAAQEAhIasKun...." set password ****** next end
Best regards
Elthon Abreu FCNSA v5
Hello,
so in that case the user will use either ssh-public-key or password for authentication?
what if i want to use only password? what would be the Parameter to set in your script?
set=password ?
Thank you
elthon.abreu wrote:Holy,
I've used the Putty Key Generation (Looking in "ProgramFiles\PuTTY" If you have putty installed). There is a variable "Key" on the script file. To create the user "bkp" you can use the config below:
config system admin edit "bkpusr" set trusthost1 "backup IP address only - for best security" set vdom "root" set ssh-public-key1 "ssh-rsa AAAAB3NzaC1yc2EAAAABJQAAAQEAhIasKun...." set password ****** next end
Best regards
NSE 8
NSE 1 - 7
You should only use the public key.
Did anyone figure out how to get the whole config with SCP for multiple vDoms ?
I get the whole config of my FGTs that have only one vDom but I also have two 300D in cluster A-A with 2 vDoms and I only get the config of one vDom with either fgt-config or sys_config.
Thank you,
Fortigate : 80E, 80F, 100E, 200F, 300E : 6.4.6
FortiAnalyzer, ForticlientEMS
I got an answer from TAC. I have to use a read-write user in order to have the whole config with multiple vDoms. The read-only user doesn't have access to the global mode therefore can't get the whole config.
Fortigate : 80E, 80F, 100E, 200F, 300E : 6.4.6
FortiAnalyzer, ForticlientEMS
Will for me the fgt-config pulls the complete configs ( full ) with vdoms.
scp <myuser>@1.1.1.1:fgt-config ./
So anything with fgt-config in the name will pull the full cfg.
e.g ( using fgt-config2 the 2 doesn't matter ;) )
scp -P 2022 admin@10.10.80.1:fgt-config2 ./ admin@10.10.80.1's password: fgt-config 100% 371KB 37.1KB/s 00:10
So anything with fgt-config or sys_config no matter what the spelling works.
kfelix$ scp -P 2022 admin@10.10.80.1:custB/sys_config ./ admin@10.10.80.1's password: sys_config 100% 371KB 33.7KB/s 00:11
kfelix$ scp -P 2022 admin@10.10.80.1:sys_config-blhblhlah ./ admin@10.10.80.1's password: sys_config 100% 371KB 37.1KB/s 00:10
Ken
PCNSE
NSE
StrongSwan
I just done that using pscp in windows
https://nbctcp.wordpress....kup-config-using-pscp/
emnoc wrote:Will for me the fgt-config pulls the complete configs ( full ) with vdoms.
scp <myuser>@1.1.1.1:fgt-config ./
So anything with fgt-config in the name will pull the full cfg.
e.g ( using fgt-config2 the 2 doesn't matter ;) )
scp -P 2022 admin@10.10.80.1:fgt-config2 ./ admin@10.10.80.1's password: fgt-config 100% 371KB 37.1KB/s 00:10
So anything with fgt-config or sys_config no matter what the spelling works.
kfelix$ scp -P 2022 admin@10.10.80.1:custB/sys_config ./ admin@10.10.80.1's password: sys_config 100% 371KB 33.7KB/s 00:11
kfelix$ scp -P 2022 admin@10.10.80.1:sys_config-blhblhlah ./ admin@10.10.80.1's password: sys_config 100% 371KB 37.1KB/s 00:10
Ken
IMHO both sys_config and fgt-config is not FULL BACKUP
Both sys_config and fgt-config are the same files
here how to test
in Forti CLI
# show full-configuration | grep ssh-public-key1 set ssh-public-key1 "ssh-rsa AAAAB3NzaC1yc2EAAAABJQAAAQEAhgCSKwiNYG7YDE0QUm2mefS8oq89dvms1+ArW/vRZ2j2AIl9a/NRMIK7whvUstVWD60HVWcGAlzpIYnCMZm3d82xifCJgSsi2QamWKzvHG27EPmn2KmXJTFdINcvK60tih89ebxGN3sPX3nv/LlyX5p3gmvcGyW019ipTEo5zFN0aMYSrkg5Xiuw3xFZhGYgNxRpSLNf1IwGcacTq+XMx58kic1QRNEnqgUrmIM1ODLpfaWm3ecq6NVTfa2UcIjPQXaweFpEgtViN5rtOi+z0oE7wm1RpbA+bM6vHeJHlBsigFqa/0Z9EY2DXtYwCM+IYzgXWF6zxtloAixDQrqi3w==" I didn't get any "ssh-public-key1" result from sys_config, fgt-config or (GUI/admin/Configuration/Backup) backup result
QUESTIONS: 1. any other method to do full config backup
UPDATE1:
-this method got full backup
# execute backup full-config tftp clifull.bak 10.0.1.1
tq
Select Forum Responses to become Knowledge Articles!
Select the “Nominate to Knowledge Base” button to recommend a forum post to become a knowledge article.
User | Count |
---|---|
1678 | |
1085 | |
752 | |
446 | |
226 |
The Fortinet Security Fabric brings together the concepts of convergence and consolidation to provide comprehensive cybersecurity protection for all users, devices, and applications and across all network edges.
Copyright 2024 Fortinet, Inc. All Rights Reserved.