60C 3G Dongel

[edox_gerard]

Hi All New to Fortigate and struggling a bit here, so any assistance will be appreciated. I have the following: FortiWifi 60C, Firmware v5.2.6,build711 (GA) MTN 3G Modem, Huawei E3531s Trying to get the system to dial on demand. **************************************************************** 1. 3G Modem not supported, so configured it as custom. config system 3g-modem custom     edit 1         set vendor "Huawei"         set model "E3531s"         set vendor-id 12d1         set product-id 15ca         set init-string "55534243123456780000000000000011062000000101000100000000000000"     next end 2. System detects the modem at least. diagnose sys modem detect diagnose sys modem query modem is attached. dialtone is detected. diagnose sys modem query USB status: Connected manufacturer: huawei model: E3531 IMEI number: xxxxxxxxxxxxxxxx SIM state: Valid service status: Valid Service signal level: 3/4 network name: MTN SA network type: UTRAN location area code: active profile(AT&V): COMMAND NOT SUPPORT 3. Modem Config config system modem set status enable set status disable set dial-on-demand enable set wireless-port 1 set connect-timeout 30 set phone1 "*99#" set username1 "MTN" set passwd1 "MTN" set extra-init1 "AT+CGDCONT=1,\"IP\",\"myMTN\""   set altmode disable 4. Keeps giving a dialing error. modemd: run_state_machine state 1(inactive) modemd: Launch modem due to manual dial. modemd: Begin dialing: redials left = 5 modemd: dev=/dev/ttyusb0 tel=*99# modemd: modem state changed: 1(inactive) -> 2(dialing) chat: abort on (BUSY) chat: abort on (NO DIAL TONE) chat: abort on (NO DIALTONE) chat: abort on (NO ANSWER) chat: abort on (ERROR) chat: send (atz^M) chat: expect (OK) chat: atz^M^M chat: OK chat:  -- got it chat: send (ath0^M) chat: abort on (NO CARRIER) chat: expect (OK) chat: ^M chat: ath0^M^M chat: OK chat:  -- got it chat: send (ats7=30^M) chat: timeout set to 30 seconds chat: expect (OK) chat: ^M chat: ats7=30^M^M chat: OK chat:  -- got it chat: send (at+cgdcont=1,"IP","internet"^M) chat: expect (OK) chat: ^M chat: at+cgdcont=1,"IP","internet"^M^M chat: OK chat:  -- got it chat: send (atdt*99#^M) chat: expect (CONNECT) chat: ^M chat: atdt*99#^M^M chat: ERROR chat:  -- failed chat: Failed (ERROR) modemd: run_state_machine state 2(dialing) modemd: Unable to connect to remote server "*99#" modemd: modem state changed: 2(dialing) -> 4(hangingup) modemd: modem_ppp_stop:465 primary modemd: redials:0  isp:1 dev:/dev/ttyusb0 tel:*99# modemd: run_state_machine state 4(hangingup) modemd: modem state changed: 4(hangingup) -> 0(uninit) modemd: run_state_machine state 0(uninit) modemd: modem state changed: 0(uninit) -> 1(inactive) modemd: run_state_machine state 1(inactive) 5. I have tried with and without credentials 6. Tried the numbers *99# and *99***1# Same results. 7. Tried APN "myMTN" and "internet", both with and without credentials. Same results. 8. Devices  fnsysctl cat /proc/bus/usb/devices T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 1 B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0 D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS= 8 #Cfgs=  1 P:  Vendor=0000 ProdID=0000 Rev= 2.04 S:  Manufacturer=Linux 2.4.37 ehci_hcd S:  Product=Fortinet USB EHCI host controller 0 S:  SerialNumber=AHB BUS C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=256ms T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 4 D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1 P:  Vendor=05e3 ProdID=0608 Rev=77.63 S:  Product=USB2.0 Hub C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  9 Spd=480 MxCh= 0 D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1 P:  Vendor=12d1 ProdID=1506 Rev= 1.02 S:  Manufacturer=HUAWEI S:  Product=HUAWEI Mobile C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=serial E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:  If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm E:  Ad=85(I) Atr=03(Int.) MxPS=  16 Ivl=32ms I:  If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm E:  Ad=85(I) Atr=03(Int.) MxPS=  16 Ivl=32ms E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=03 Driver=serial E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=02 Driver=serial E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us I:  If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=125us T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=  4 Spd=480 MxCh= 0 D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1 P:  Vendor=1307 ProdID=0310 Rev= 1.00 S:  Manufacturer=Generic S:  Product=Mass Storage Device S:  SerialNumber=00000000000006 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

[edox_gerard]

Hi All

Must confess that I a bit disappointed at the lack of assistance, especially on a manufacturers forum.

But regardless, herewith the end solution in case some other poor schlep comes across this issue.

Tested on both a Huawei E3531 and E3131 modem.

#####################################################################################################

config system modem

    set status enable

    set auto-dial enable

    set phone1 "*99#"

    set dial-cmd1 "atd"

end

config system 3g-modem custom

    edit 1

        set vendor "Huawei"

        set model "E3131"

        set vendor-id 12d1

        set product-id 15ca

        set init-string "55534243123456780000000000000a11062000000000000100000000000000"

    next

end

#####################################################################################################

config router static

    edit 3

        set device "modem"

        set comment "Huawei 3G Modem"

    next

end

#####################################################################################################

config system link-monitor

    edit "wan1 check"

        set srcintf "wan1"

        set server "8.8.8.8"

        set protocol ping

        set gateway-ip x.x.x.x

        set source-ip 0.0.0.0

        set interval 5

        set timeout 5

        set failtime 5

        set recoverytime 1

        set ha-priority 1

        set update-cascade-interface enable

        set update-static-route enable

        set status enable

    next

end

#####################################################################################################

[Lucascat]

Hello Gerad I've tried with HUAWEI E3531 on 60D 5.6.7 without success.

Can you help me?