Skip to main content
UnderscoresAndDashes
Explorer
September 5, 2024
Question

Some SDWAN(BGP) routes discovered on wan interface.

My issue is that if I have 2 dialup tunnels on a remote gate, each dialup is connected to a seperate ISP, if I lose the primary ISP that is connected to dialup tunnel 1 and dialup tunnel 2 (seperate ISP) picks up the routing, then some routes are discovered on the correct dialup interface, but others show as being discovered via the wan interface.

I am not sure what the problem is. 

See below:

 

SDWANRouting issue.png

 This is in a test environment. The gates are on 7.2.8 

 

Remote Gate

config vpn ipsec phase1-interface
edit "advpn_1"
set interface "wan1"
set peertype any
set net-device disable
set proposal aes256-sha256
set add-route disable
set auto-discovery-receiver enable
set remote-gw x.x.x.x

next

end

 

config vpn ipsec phase2-interface
edit "advpn_1_p2"
set phase1name "advpn_1"
set proposal aes256-sha256
set auto-negotiate enable
next
end

 

config vpn ipsec phase1-interface

edit "advpn_2"
set interface "wan2"
set peertype any
set net-device disable
set proposal aes256-sha256
set add-route disable
set auto-discovery-receiver enable
set remote-gw x.x.x.x

next

end

 

config vpn ipsec phase2-interface
edit "advpn_2_p2"
set phase1name "advpn_1"
set proposal aes256-sha256
set auto-negotiate enable
next
end

 

Hub Dialup config

config vpn ipsec phase1-interface

edit "advpn_1"
set type dynamic
set interface "port1"
set peertype any
set net-device disable
set proposal aes256-sha256
set add-route disable
set dpd on-idle
set auto-discovery-sender enable
set auto-discovery-receiver enable

set dpd-retryinterval 60
next
end

 

config vpn ipsec phase2-interface
edit "advpn_1_p2"
set phase1name "advpn_1"
set proposal aes256-sha256
next
end

 

config vpn ipsec phase1-interface

edit "advpn_2"
set type dynamic
set interface "port2"
set peertype any
set net-device disable
set proposal aes256-sha256
set add-route disable
set dpd on-idle
set auto-discovery-sender enable
set auto-discovery-receiver enable

set dpd-retryinterval 60
next
end

 

config vpn ipsec phase2-interface
edit "advpn_2_p2"
set phase1name "advpn_2"
set proposal aes256-sha256
next
end

 

Thank you for any help. 

 

2 replies

UnderscoresAndDashes
Explorer
September 5, 2024

Should also mention that remote gate dialup tunnels are in an SDWAN zone, have an SLA and a SDWAN rule based on best quality. Routing works correctly regardless of which dialup is selected by the rule, unless I lose an ISP and one tunnel goes down. Then routing gets all weird. 

holmes
Visitor III
November 4, 2024

Hi,

 

I'm sure this is because your SLA option: update static route is enabled, I have the same problem before, disabled it and problem solved.

 

Goodluck.

Thought Leadership. Security Summit. Thursday, November 12th, PGA National Resort, Palm Beach Gardens, FL.
Thought Leadership. Security Summit. Thursday, October 8th. Disney's Grand Californian Hotel & SPA, Anaheim, CA.
Security Operations Summit: Modernize SecOps. Operate AI-Native.AMER: November 4 | 9:00 AM PST. India and SAARC: November 5 | 10:00 AM IST. EMEA: November 5 | 10:30 AM CET. APAC: November 5 | 11:00 AM SGT