Skip to main content
A
Anonymous_User
New Contributor III
July 10, 2008
Solved

Fortimail 100 & Exchange Outgoing SMTP

  • July 10, 2008
  • 5 replies
  • 4589 views
I' ve got a Fortimail 100 on evaluation for the next week, have it running in gateway mode behind a firewall (Fortigate 300A) and is scanning externally send incoming email no problems on Exchange 2003. The problem I have is that it isnt scanning internally sent outbound mail, the admin guide says configure the email client' s outgoing smtp server to be the Fortimail but I can' t see how Exchange lets you do this. Any replies would be greatly appreciated. Cheers Dan
    Best answer by Anonymous_User
    UK is right... Just create a new access rule (Mail Settings --> Access) and set the following values: - Sender Pattern: * - leave the " Regular expression" box unchecked - Recipient Pattern: * - leave the " Regular expression" box unchecked - Sender IP/Netmask: ip adress of the Exchange server /32 - leave the " Regular expression" box unchecked - set Action to " RELAY" Change the SMTP Connector on the exchange to the Fortimail and than just test the whole thing. That should be all.

    5 replies

    UkWizard
    UkWizard
    New Member
    July 10, 2008
    you need to configure exchange to not deliver directly, but forward to that ' smart' host. under connectors, edit the SMTP one, in the general tab, tick the " forward all mail through this comnector" and put in the fortimail ip. but make sure fortimail is configured to allow the outbound as well. else it will all start bouncing back.
    A
    Anonymous_UserAuthor
    New Contributor III
    July 11, 2008
    Hi UKWizard, like daniel I also want to pass mails from an exchange server to the fortimail which then is sending the mails to the next smtp server. I' ve changed the exchange smtp connector to use the fortimail but the mails will be rejected from the fortimail. What settings needs to be made to the fortimail to let the unit pass through? Regards Tom
    UkWizard
    UkWizard
    New Member
    July 11, 2008
    I am a bit rusty on the fortimails, having not installed many. But you need to create an outbound policy, just like with the inbound. and add your exchange server IP somewhere to allow it to relay. Sorry its a bit vague, but its been a while. the manual should explain all of this, it can be found here; http://docs.forticare.com/fmail.html Anything else i would need to dig my notes out :)
    A
    Anonymous_UserAuthor
    New Contributor III
    July 11, 2008
    Thanks for the info UkWizard, I' ve applied that setting this morning and now when sending mail out of the Exchange server to an external mail server I' m getting - Your message did not reach some or all of the intended recipients. Subject: Sent: 7/11/2008 9:03 AM The following recipient(s) could not be reached: daniel.coyle@hotmail.co.uk on 7/11/2008 9:03 AM You do not have permission to send to this recipient. For assistance, contact your system administrator. <ex1.Weston-Test.co.uk #5.7.1 smtp;550 5.7.1 <daniel.coyle@hotmail.co.uk>... Relaying denied> I didnt have an SMTP connector set up so have created one and defined the Fortimail as the smarthost, have also defined the fortimail as a relay server and smarthost in the smtp v server properties. I can now see mail sent internally to external addresses on the fortimail logs....any advice would be greatly appreciated! Thanks Dan
    UkWizard
    UkWizard
    New Member
    July 11, 2008
    Last time i installed one, it was under; MAIL SERVER -> ACCESS Then adding a relay permission from the mailserver IP. It must be in the manual though. I have a fortimail in the office in a box, but i dont have time to get it out to check it out exactly, sorry.
    A
    Anonymous_UserAuthorAnswer
    New Contributor III
    July 15, 2008
    UK is right... Just create a new access rule (Mail Settings --> Access) and set the following values: - Sender Pattern: * - leave the " Regular expression" box unchecked - Recipient Pattern: * - leave the " Regular expression" box unchecked - Sender IP/Netmask: ip adress of the Exchange server /32 - leave the " Regular expression" box unchecked - set Action to " RELAY" Change the SMTP Connector on the exchange to the Fortimail and than just test the whole thing. That should be all.
    Terms & ConditionsAccessibility statement