Fortigate IPsec Dial-in behind NAT, no outgoing data
Hi,
Have an Issue with an IPSec Site-to-Site between set of Fortigate units:
1 x 200E behind a public IP / LAN 10.184.0.0/16
1 x 60F behind a dynamic, natted IP. / LAN 10.151.0.0/16
I'm running 7.0.2
I've established the tunnel, using dial-in from the 60F, all easy enough.
Problem is that it seems no traffic is exiting the 200E, over the tunnel (outgoing data remains at 0).
In the other direction It seems to work fine (so from 60F to 200E)
I've checked policies, and done some packet sniffing, and all the policies are fine, the packets enter the tunnel, I can see this in a sniff capture as well as in the counters of the policies. However, when I sniff on the WAN port, no outgoing data whatsoever. It seems like the data is entering the tunnel but not encapsulated on the WAN port?
This is the Sniffer on the Tunnel IF.
MeetMe-FGT200E # diagnose sniffer packet VPN-TO-Korea
interfaces=[VPN-TO-Korea]
filters=[none]
pcap_lookupnet: VPN-TO-Korea: no IPv4 address assigned
4.932745 10.212.134.201.45392 -> 10.151.100.250.443: syn 2100634384
4.932758 10.212.134.201.45386 -> 10.151.100.250.443: syn 85500106
20.701265 10.212.134.201.58654 -> 10.151.0.1.22: syn 2136697446
21.706119 10.212.134.201.58654 -> 10.151.0.1.22: syn 2136697446
35.072702 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
37.359246 10.212.134.201.45386 -> 10.151.100.250.443: syn 85500106
37.359539 10.212.134.201.45392 -> 10.151.100.250.443: syn 2100634384
38.072951 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
41.073175 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
44.073315 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
47.073525 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
49.510687 10.212.134.201.37728 -> 10.151.100.250.443: syn 268559521
49.763256 10.212.134.201.37738 -> 10.151.100.250.443: syn 1569137478
50.073776 10.184.21.249.60313 -> 10.151.0.1.22: syn 765367915
50.532805 10.212.134.201.37728 -> 10.151.100.250.443: syn 268559521
50.772685 10.212.134.201.37738 -> 10.151.100.250.443: syn 1569137478
51.546010 10.212.134.201.37728 -> 10.151.100.250.443: syn 268559521
51.785989 10.212.134.201.37738 -> 10.151.100.250.443: syn 1569137478
52.559335 10.212.134.201.37728 -> 10.151.100.250.443: syn 268559521
52.799274 10.212.134.201.37738 -> 10.151.100.250.443: syn 1569137478
Sniffer on the WAN is empty for the gateway destination (173.221.174.130)
Here is the vpn config (omitted keys and changed public ip's:
MeetMe-FGT200E # get vpn ipsec tunnel details
gateway
name: 'VPN-TO-Korea_0'
local-gateway: 173.221.174.132:4500 (static)
remote-gateway: 173.221.174.130:64916 (dynamic)
dpd-link: on
mode: ike-v1
interface: 'wan1' (17)
rx packets: 0 bytes: 0 errors: 0
tx packets: 0 bytes: 0 errors: 0
dpd: on-idle/negotiated idle: 60000ms retry: 3 count: 0
nat traversal mode: silent RFC 3947
selectors
name: 'VPN-TO-Korea'
auto-negotiate: disable
mode: tunnel
src: 0:10.184.0.0/255.255.0.0:0
dst: 0:10.151.0.0/255.255.0.0:0
Am I missing something?
