Dialup user aggressive mode IPsec between FortiGate and Cisco router

I`ve found the solution finally. But now I`m facing a new issue: OSPF doesn`t bring up.

I am using Dial Up user IPsec VPN with aggressive mode. Also I have cofigured static addresses for tunnel interfaces on FortiGate and on Cisco router. This config is for test environment. Aggressive mode + Dialup user is customers requirements so I can`t stand back from it. 

Configuratons are following:

=================================Cisco========================== ! crypto keyring KEYR1   pre-shared-key address 192.168.70.201 key aq1sw2de3 ! ! crypto isakmp policy 10  encr 3des  hash md5  authentication pre-share  group 2 crypto isakmp profile ISAKMP_PROF    keyring KEYR1    self-identity user-fqdn hub-cisco    match identity address 192.168.70.201 255.255.255.0    initiate mode aggressive ! ! crypto ipsec transform-set TEST-SET esp-3des esp-md5-hmac  mode tunnel ! ! crypto ipsec profile TEST-PROFILE  set transform-set TEST-SET  set pfs group2  set isakmp-profile ISAKMP_PROF ! interface Tunnel0  ip address 10.0.100.2 255.255.255.0  ip ospf network point-to-point  ip ospf mtu-ignore  tunnel source GigabitEthernet1  tunnel mode ipsec ipv4  tunnel destination 192.168.70.201  tunnel protection ipsec profile TEST-PROFILE end ! interface GigabitEthernet1  ip address 192.168.70.216 255.255.255.0  negotiation auto ! ! router ospf 10  router-id 10.0.201.3  passive-interface GigabitEthernet2  network 10.0.100.0 0.0.0.3 area 0 ! ip route 0.0.0.0 0.0.0.0 192.168.70.1 !

======================FG================================ config vpn ipsec phase1-interface     edit "agg-to-ISR"         set type dynamic         set interface "port10"         set nattraversal disable         set mode aggressive         set peertype one         set proposal 3des-md5         set add-route disable         set dpd disable         set dhgrp 2         set peerid "hub-cisco"         set psksecret ENC ***     next config vpn ipsec phase2-interface     edit "agg-to-ISR"         set phase1name "agg-to-ISR"         set proposal 3des-md5         set dhgrp 2     next end config system interface     edit "port10"         set vdom "root"         set ip 192.168.70.201 255.255.255.0         set allowaccess ping https ssh fgfm capwap         set type physical         set alias "wan1-LOCAL-DHCP"         set device-identification enable         set snmp-index 10     next       edit "agg-to-ISR"         set vdom "root"         set ip 10.0.100.1 255.255.255.255         set allowaccess ping https ssh         set l2forward enable         set type tunnel         set remote-ip 10.0.100.2         set snmp-index 14         set interface "port10"     next config firewall policy     edit 10         set srcintf "agg-to-ISR"         set dstintf "any"         set srcaddr "all"         set dstaddr "all"         set action accept         set schedule "always"         set service "ALL"     next     edit 15         set srcintf "any"         set dstintf "agg-to-ISR"         set srcaddr "all"         set dstaddr "all"         set action accept         set schedule "always"         set service "ALL"     next  config router ospf     set default-information-originate enable     set router-id 10.0.201.1         config area             edit 0.0.0.0             next         end         config ospf-interface             edit "agg-to-ISR"                 set interface "agg-to-ISR"                 set mtu-ignore enable                 set network-type point-to-point             next         end         config network             edit 3                 set prefix 10.0.100.0 255.255.255.252             next             edit 6                 set prefix 172.16.0.0 255.255.255.0 #using it for another router             next         end         config redistribute "connected"             set status enable         end         config redistribute "static"             set status enable         end         config redistribute "rip"         end         config redistribute "bgp"         end         config redistribute "isis"         end end

There is following output for OSPF debug on fortigate:

# get router info ospf interface

agg-to-ISR is down, line protocol is down
  Internet Address 10.0.100.1/32, Area 0.0.0.0, MTU 1500
  Process ID 0, Router ID 10.0.201.1, Network Type POINTOPOINT, Cost: 0
  Transmit Delay is 1 sec, State Down
  Timer intervals configured, Hello 10.000, Dead 40, Wait 40, Retransmit 5

# exec ping 10.0.100.2

PING 10.0.100.2 (10.0.100.2): 56 data bytes
64 bytes from 10.0.100.2: icmp_seq=0 ttl=255 time=2.7 ms
64 bytes from 10.0.100.2: icmp_seq=1 ttl=255 time=3.3 ms
64 bytes from 10.0.100.2: icmp_seq=2 ttl=255 time=3.2 ms
64 bytes from 10.0.100.2: icmp_seq=3 ttl=255 time=3.0 ms
64 bytes from 10.0.100.2: icmp_seq=4 ttl=255 time=3.1 ms

--- 10.0.100.2 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 2.7/3.0/3.3 ms

Cisco router costantly sends multicast messages to fortigate, but there is no reverse traffic:

# diagnose sniffer packet any 'host 10.0.100.2' 4

interfaces=[any]
filters=[host 10.0.100.2]
3.127230 agg-to-ISR_0 in 10.0.100.2 -> 224.0.0.5: ip-proto-89 56
13.038071 agg-to-ISR_0 in 10.0.100.2 -> 224.0.0.5: ip-proto-89 56
22.633617 agg-to-ISR_0 in 10.0.100.2 -> 224.0.0.5: ip-proto-89 56
31.731950 agg-to-ISR_0 in 10.0.100.2 -> 224.0.0.5: ip-proto-89 56
41.437651 agg-to-ISR_0 in 10.0.100.2 -> 224.0.0.5: ip-proto-89 56

I`m frustrated as Benoit_Rech_FTNT mentioned in this post https://forum.fortinet.com/tm.aspx?m=111570

that IKE Mode Configuration should be used. I can`t find ways to realise it on Cisco router.

Does anyone have any suggestions on it ?