BGP not using public IP address on outgoing IF

emnoc wrote:

Qs:

 

[ul]

You mention BGP but is this a SNAT related issue?[/ul][ul]

Did you run diag debug flow[/ul][ul]

Are the networks your advertising are they show up on a route-server/looking-glass[/ul][ul]

The ippool that your SNAT is it being advertised?[/ul]

 

For the later, you might have to  define a loopback address and static the ippool /24s behind that interface. BGP will need the route in the local route-table in order to advertise it.

Hello! Thanks for quick reply.

1. Basically it is probalby a SNAT issue, I've tried this: http://kb.fortinet.com/kb/microsites/search.do?cmd=displayKC&docType=kc&externalId=11969&sliceId=1&docTypeID=DT_KCARTICLE_1_1&dialogID=24810224&stateId=0%200%2024812128 but network goes down, probably by routing loop?

BGP device X.Y.Z.190 = route dest X.Y.Z.0/24 next-hop X.Y.Z.129 FW device 10.0.0.1 = route dest 0.0.0.0 next-hop X.Y.Z.190

2. I did not run the diag debug flow, I'm reading the manual for now, can you send me the whole command and what to search?

3. The routing on FortiGate looks like this:

FG # get router info routing-table all | grep X.Y.Z.
B X.Y.Z.0/24 [20/0] is a summary, Null, 19:48:39
S X.Y.Z.0/26 [10/0] via X.Y.Z.129, port3
C X.Y.Z.128/26 is directly connected, port3
S X.Y.Z.240/29 [10/0] via X.Y.Z.129, port3

FG #

And this is my FG BGP configuration...:

config router bgp
    set as 00000
    set router-id X.Y.Z.190
    set keepalive-timer 45
    set holdtime-timer 120
    set bestpath-med-missing-as-worst enable
    set log-neighbour-changes enable
    set graceful-restart enable
        config aggregate-address
            edit 1
                set prefix X.Y.Z.0 255.255.255.0
                set as-set enable
            next
        end
        config neighbor
            edit "3.3.3.33"
                set description "ISP3"
                set remote-as 33333
                set send-community6 disable
                set keep-alive-timer 45
                set holdtime-timer 120
                set connect-timer 60
                set weight 50
            next
            edit "2.2.2.157"
                set description "ISP2"
                set remote-as 222222
                set send-community6 disable
                set keep-alive-timer 45
                set holdtime-timer 120
                set connect-timer 60
                set weight 100
            next
            edit "1.1.1.161"
                set next-hop-self enable
                set description "ISP1"
                set remote-as 11111
                set send-community6 disable
                set keep-alive-timer 45
                set holdtime-timer 120
                set connect-timer 60
                set weight 250
            next
        end
        config network
            edit 1
                set prefix X.Y.Z.0 255.255.255.0
            next
        end
        config redistribute "connected"
        end
        config redistribute "rip"
        end
        config redistribute "ospf"
        end
        config redistribute "static"
            set status enable
        end
        config redistribute "isis"
        end
        config redistribute6 "connected"
        end
        config redistribute6 "rip"
        end
        config redistribute6 "ospf"
        end
        config redistribute6 "static"
        end
        config redistribute6 "isis"
        end
    set graceful-stalepath-time 180
    set graceful-update-delay 180
end

I think I'm missing something, maybe this SNAT as you said, but how to implement this is the network goes down... Basically also maybe the route isn't advertised correctly? I can use X.Y.Z.0/24 on the Internet, but only outgoing interface is not working with this address (X.Y.Z.129) and the SMTP server also (X.Y.Z.189) - I land in a blacklist because of ISP interface being used.

This is my old configuration which is working correctly, but the device is too old :)

interfaces {
    ge-0/0/0 {
        unit 0 {
            family inet {
                address 10.100.140.254/24;
            }
        }
    }
    ge-0/0/1 {
        description INSITE;
        unit 0 {
            description INSITE_if;
            family inet {
                address X.Y.Z.190/26;
            }
        }
    }
    ge-0/0/2 {
        description ISP2;
        unit 0 {
            description ISP2;
            family inet {
                address 2.2.2.158/30;
            }
        }
    }
    ge-0/0/3 {
        description ISP1;
        unit 0 {
            description ISP1;
            family inet {
                address 1.1.1.162/30;
            }
        }
    }
    lo0 {
        unit 0 {
            family inet {
                address 127.0.0.1/32;
            }
        }
    }
}
routing-options {
    static {
        route X.Y.Z.0/26 next-hop X.Y.Z.129;
        route 10.0.0.0/8 next-hop 10.100.140.1;
        route X.Y.Z.240/29 next-hop X.Y.Z.129;
    }
    aggregate {
        route X.Y.Z.0/24;
    }
    router-id X.Y.Z.190;
    autonomous-system XXXXX loops 1;
}
protocols {
    bgp {
        accept-remote-nexthop;
        group NETIA {
            type external;
            export [ R_PUB_POLICY REJECT_ALL ];
            neighbor 1.1.1.161 {
                peer-as 11111;
            }
        }
        group MULTIPLAY {
            type external;
            export [ R_PUB_POLICY REJECT_ALL ];
            neighbor 2.2.2.157 {
                peer-as 222222;
            }
        }
    }
}
policy-options {
    prefix-list R_PUB {
        X.Y.Z.0/24;
    }
    policy-statement R_PUB_POLICY {
        from {
            protocol aggregate;
            prefix-list R_PUB;
        }
        then accept;
    }
    policy-statement REJECT_ALL {
        then reject;
    }
}
security {
    screen {
        ids-option untrust-screen {
            icmp {
                ping-death;
            }
            ip {
                source-route-option;
                tear-drop;
            }
            tcp {
                syn-flood {
                    alarm-threshold 1024;
                    attack-threshold 200;
                    source-threshold 1024;
                    destination-threshold 2048;
                    queue-size 2000;
                    timeout 20;
                }
                land;
            }
        }
    }
    zones {
        security-zone trust {
            tcp-rst;
            host-inbound-traffic {
                system-services {
                    all;
                }
                protocols {
                    all;
                }
            }
            interfaces {
                ge-0/0/0.0 {
                    host-inbound-traffic {
                        system-services {
                            http;
                            https;
                            ssh;
                            telnet;
                            dhcp;
                        }
                    }
                }
                ge-0/0/1.0;
                ge-0/0/2.0 {
                    host-inbound-traffic {
                        system-services {
                            ping;
                        }
                        protocols {
                            bgp;
                        }
                    }
                }
                ge-0/0/3.0 {
                    host-inbound-traffic {
                        system-services {
                            ping;
                        }
                        protocols {
                            bgp;
                        }
                    }
                }
            }
        }
        security-zone untrust {
            screen untrust-screen;
            host-inbound-traffic {
                system-services {
                    all;
                }
                protocols {
                    all;
                }
            }
        }
    }
    policies {
        from-zone trust to-zone trust {
            policy default-permit {
                match {
                    source-address any;
                    destination-address any;
                    application any;
                }
                then {
                    permit;
                }
            }
        }
        from-zone trust to-zone untrust {
            policy ban-ntp {
                match {
                    source-address any;
                    destination-address any;
                    application [ junos-nntp junos-ntp junos-ms-sql ];
                }
                then {
                    deny;
                }
            }
            policy default-permit {
                match {
                    source-address any;
                    destination-address any;
                    application any;
                }
                then {
                    permit;
                }
            }
        }
        from-zone untrust to-zone trust {
            policy ban-ntp {
                match {
                    source-address any;
                    destination-address any;
                    application [ junos-ntp junos-nntp junos-ms-sql ];
                }
                then {
                    deny;
                }
            }
            policy default-deny {
                match {
                    source-address any;
                    destination-address any;
                    application any;
                }
                then {
                    permit;
                }
            }
        }
        default-policy {
            deny-all;
        }
    }
}

emnoc wrote:

1st let's start by seeing what your sending via BGP. The distribution of  BGP is one thing, the SNAT is another ( ip pools ).

 

So are you sending the prefix that contains the nat-pool ?

 

 get router info bgp neighbors

 get router info bgp network

 diagnostic reset

 diagnose ip router bgp  events < insert ipv4 address/prefix>

 diagnostic enable

 

If that looks good, run the diagnostic flow command against one host that sending traffic that should be SNAT

 

 diag debug dis

 diag debug reset

 diag debug flow filter addr <x.y.x.x>

 diag debug flow show console enabl

 diag debug enable

 diag debug flow trace start 100

 

Now start some traffic and review and capture the output.

 

When done reset diagnostics

 

 diag debug disable

 diag debug reset

 

Start withe the above, I'm assuming the summary route in your route-table is the prefixes your sending and covers the ip-pool range?

 

Thank you for a quick learning guide, I will do this, but basically I disabled the NAT on the policy LAN->WAN and it started to work! This post: https://forum.fortinet.co...p;m=128453&mpage=1