60C 3G Dongel
Hi All New to Fortigate and struggling a bit here, so any assistance will be appreciated. I have the following: FortiWifi 60C, Firmware v5.2.6,build711 (GA) MTN 3G Modem, Huawei E3531s Trying to get the system to dial on demand. **************************************************************** 1. 3G Modem not supported, so configured it as custom. config system 3g-modem custom edit 1 set vendor "Huawei" set model "E3531s" set vendor-id 12d1 set product-id 15ca set init-string "55534243123456780000000000000011062000000101000100000000000000" next end 2. System detects the modem at least. diagnose sys modem detect diagnose sys modem query modem is attached. dialtone is detected. diagnose sys modem query USB status: Connected manufacturer: huawei model: E3531 IMEI number: xxxxxxxxxxxxxxxx SIM state: Valid service status: Valid Service signal level: 3/4 network name: MTN SA network type: UTRAN location area code: active profile(AT&V): COMMAND NOT SUPPORT 3. Modem Config config system modem set status enable set status disable set dial-on-demand enable set wireless-port 1 set connect-timeout 30 set phone1 "*99#" set username1 "MTN" set passwd1 "MTN" set extra-init1 "AT+CGDCONT=1,\"IP\",\"myMTN\"" set altmode disable 4. Keeps giving a dialing error. modemd: run_state_machine state 1(inactive) modemd: Launch modem due to manual dial. modemd: Begin dialing: redials left = 5 modemd: dev=/dev/ttyusb0 tel=*99# modemd: modem state changed: 1(inactive) -> 2(dialing) chat: abort on (BUSY) chat: abort on (NO DIAL TONE) chat: abort on (NO DIALTONE) chat: abort on (NO ANSWER) chat: abort on (ERROR) chat: send (atz^M) chat: expect (OK) chat: atz^M^M chat: OK chat: -- got it chat: send (ath0^M) chat: abort on (NO CARRIER) chat: expect (OK) chat: ^M chat: ath0^M^M chat: OK chat: -- got it chat: send (ats7=30^M) chat: timeout set to 30 seconds chat: expect (OK) chat: ^M chat: ats7=30^M^M chat: OK chat: -- got it chat: send (at+cgdcont=1,"IP","internet"^M) chat: expect (OK) chat: ^M chat: at+cgdcont=1,"IP","internet"^M^M chat: OK chat: -- got it chat: send (atdt*99#^M) chat: expect (CONNECT) chat: ^M chat: atdt*99#^M^M chat: ERROR chat: -- failed chat: Failed (ERROR) modemd: run_state_machine state 2(dialing) modemd: Unable to connect to remote server "*99#" modemd: modem state changed: 2(dialing) -> 4(hangingup) modemd: modem_ppp_stop:465 primary modemd: redials:0 isp:1 dev:/dev/ttyusb0 tel:*99# modemd: run_state_machine state 4(hangingup) modemd: modem state changed: 4(hangingup) -> 0(uninit) modemd: run_state_machine state 0(uninit) modemd: modem state changed: 0(uninit) -> 1(inactive) modemd: run_state_machine state 1(inactive) 5. I have tried with and without credentials 6. Tried the numbers *99# and *99***1# Same results. 7. Tried APN "myMTN" and "internet", both with and without credentials. Same results. 8. Devices fnsysctl cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1 B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.04 S: Manufacturer=Linux 2.4.37 ehci_hcd S: Product=Fortinet USB EHCI host controller 0 S: SerialNumber=AHB BUS C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05e3 ProdID=0608 Rev=77.63 S: Product=USB2.0 Hub C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1506 Rev= 1.02 S: Manufacturer=HUAWEI S: Product=HUAWEI Mobile C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=serial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm E: Ad=85(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm E: Ad=85(I) Atr=03(Int.) MxPS= 16 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=03 Driver=serial E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=02 Driver=serial E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=125us T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1307 ProdID=0310 Rev= 1.00 S: Manufacturer=Generic S: Product=Mass Storage Device S: SerialNumber=00000000000006 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms