Skip to main content
gmonte
Staff
Staff
January 26, 2026

Troubleshooting Tip: Port displays Up status (Green LED) with no cable connected

  • January 26, 2026
  • 1 reply
  • 786 views
Description

This article describes the behavior observed in versions 7.4 and 7.6, where some ports report the link status as Up, and the interface LED is green, but no SFP is plugged in.

Scope FortiGate 400F/401F, FortiGate 600F/601F.
Solution

Based on the picture and CLI outputs below, no SFP is plugged in, yet the link status is shown as Up. Additionally, on the FortiGate, the port's LED appears green even though nothing is connected to the port.

 

Link statu.PNG

 

Note 1: In some cases, the port flaps are permanently down.

 

Note 2: To reboot the device may return to normal, but after some time, the issue automatically reappears.

 

FGT_A # get system interface transceiver x7
Interface x7 - Transceiver is not detected.

FGT_A # show system interface x7
config system interface
    edit "x7"
        set vdom "root"
        set type physical
        set mediatype sr
        set snmp-index 33
        set speed 10000full
    next
end

FGT_A # show system interface x7
config system interface
    edit "x7"
        set vdom "root"
        set type physical
        set mediatype sr
        set snmp-index 33
        set speed 10000full
    next
end

FGT_A # fnsysctl ifconfig x7
x7 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
        UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
        RX packets:176 errors:0 dropped:0 overruns:0 frame:0
        TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
        collisions:0 txqueuelen:1000
        RX bytes:22176 (21.7 KB) TX bytes:786 (786 Bytes)

FGT_A # diagnose hardware deviceinfo nic x7
Description :FortiASIC NP7 Adapter
Driver Name :FortiASIC Unified NPU Driver
pid :31
oid :158
vid :4030
macid :30
eif_id :2
promiscous :1
local_port :1
vlan_wa_done :0
mtu :1500
netdev oid :158
dev-flags :1103
dev-promis :1
Current_HWaddr xx:xx:xx:xx:xx:xx
Permanent_HWaddr xx:xx:xx:xx:xx:xx
==== Default Link Settings =====
auto-nego :Disable
s_speed :10000
s_duplex :Full
==== Current Link Settings =====
auto-nego :Disable
s_status :Up
s_speed :10000
s_duplex :Full
FEC :OFF (0x2)
FEC_cap :NONE (0x1)
SerDes_if :SR
SerDes_if_cap :GMII,SGMII,SR,LR,CR (0x3e)
SerDes_dflt :3
pm_mode_setting :0
pm_mode :0x0
pm_mode_dflt :0
pm_port :No
medium_mode :0
==== Link Status ===============
Admin :Up
link_status :Up
Speed :10000
Duplex :Full
==== Netdev Status =============
dev_running :Yes
dev_carrier :On
==== Host Counters =============
hrx_pkts :88
hrx_bytes :10032
htx_pkts :7
htx_bytes :786
htx_drop :0
htx_e_busy :0
htx_e_noheadroom:0
htx_e_oid :0
htx_e_adapter :0
htx_e_pad :0
htx_e_other :0
==== Netdev Counters ===========
Rx Pkts :176
Rx Bytes :22176
Tx Pkts :7
Tx Bytes :786
==== Transceiver Info ==========
tx_disable : N/A
rx_los : N/A
tx_fault : N/A
present : N/A
last_spd : 0

FGT_A # get system interface physical x7
== [onboard]
        ==[x7]
                mode: static
                ip: 0.0.0.0 0.0.0.0
                ipv6: ::/0
                status: up
                speed: 10000Mbps (Duplex: full)
                FEC: none
                FEC_cap: {none}

 

There will be no fix for firmware v7.2.

The issue can be fixed by upgrading to the FortiOS versions 7.4.8 or 7.6.5.

1 reply

edvancesecurity_support
New Member
April 24, 2026

Hi Sir,

 

We are facing same issue on FortiGate 401F but the firmware were 7.6.6.