Troubleshooting Tip: FortiADC IP troubleshooting, ARP, Routing Table

Description

This article describes some basic commands for troubleshooting IP Routing, ARP and Interface configuration.

Scope

FortiADC.

Solution

Show IP interface configuration:

Example:

FortiADC-VM # diagnose netlink ip list

IP=127.0.0.1 MASK=255.255.255.0 index=1 devname=lo
IP=127.129.1.1 MASK=255.255.255.255 index=1 devname=lo
IP=192.168.157.78 MASK=255.255.255.0 index=4 devname=port1
IP=172.16.100.100 MASK=255.255.255.255 index=4 devname=port1
IP=172.16.100.100 MASK=255.255.255.0 index=5 devname=port5
IP=192.168.82.100 MASK=255.255.255.0 index=7 devname=port2
IP=10.10.10.100 MASK=255.255.255.0 index=9 devname=port10
IP=169.254.59.16 MASK=255.255.0.0 index=17 devname=haport0
IP=172.30.10.79 MASK=255.255.255.0 index=18 devname=VLAN_10

FortiADC-VM (root) # get router info routing-table kernel-connected

C       10.10.10.0/24 dev port10  proto kernel  scope link  src 10.10.10.100
C       169.254.0.0/16 dev haport0  proto kernel  scope link  src 169.254.59.16
C       172.16.100.0/24 dev port5  proto kernel  scope link  src 172.16.100.100
C       172.30.10.0/24 dev VLAN_10  proto kernel  scope link  src 172.30.10.79
C       192.168.82.0/24 dev port2  proto kernel  scope link  src 192.168.82.100
C       192.168.157.0/24 dev port1  proto kernel  scope link  src 192.168.157.78

The address MAC of a specific interface:

get system interface port5:

type                          : physical
mode                          : static
vdom                          : root
redundant-master              :
ip                            : 172.16.100.100/24
ip6                           : ::/0
allowaccess                   : https ping ssh snmp http telnet
mtu                           : 1500
speed                         : auto
status                        : up
mac-addr                      : 00:0c:29:55:3b:38
secondary-ip                  : disable
ha-node-secondary-ip          : disable

ARP cache table:

FortiADC-VM (root) # diagnose netlink neighbor list

ifindex=9 ifname=port10 10.10.10.80 00:50:56:c0:00:0a state=00000004 use=5653 confirm=11653 update=5653 ref=0
ifindex=1 ifname=lo 192.168.157.78 00:00:00:00:00:00 state=00000040 use=5668 confirm=11668 update=5668 ref=0
ifindex=5 ifname=port5 172.16.100.1 00:0c:29:5b:36:cc state=00000002 use=626 confirm=626 update=626 ref=1
ifindex=5 ifname=port5 172.16.100.80 00:50:56:c0:00:05 state=00000004 use=4169 confirm=10169 update=78 ref=0
ifindex=4 ifname=port1 192.168.157.1 state=00000001 use=53 confirm=16375 update=253 ref=1
ifindex=1 ifname=lo 172.16.100.100 00:00:00:00:00:00 state=00000040 use=5493 confirm=11493 update=5493 ref=0

Display IP routing table: routing table 

(M) FortiADC-VM (root) # get router info routing-table all

Codes: K - kernel route, C - connected, S - static, O - OSPF, P - PPPoE
       i - isp route, > - selected route, * - FIB route
 
S   0.0.0.0/0 [10/0] via 192.168.157.1 inactive
C>* 10.10.10.0/24 is directly connected, port10
C>* 169.254.0.0/16 is directly connected, haport0
C>* 172.16.100.0/24 is directly connected, port5
C>* 192.168.82.0/24 is directly connected, port2